Nuvair Pro CO Скачать руководство пользователя страница 20

Страница: 20 / 24

Pro CO Carbon Monoxide Analyzer

www.nuvair.com

9.0 Spares and Accessories

9.1. Sensors

Sensor replacement for Pro CO
Part Number:

9501-50

9.2. Calibration Equipment

Calibration requires certified CO calibration gas to be
delivered at a specific flow rate and pressure.

A variety of calibration gas canisters are available
from Nuvair, with compatible Flow Restrictor/
Regulator assemblies to regulate the gas.

10.0 Troubleshooting

SYMPTOM

REASON

SOLUTION

Battery symbol

Low Battery

Change the battery

No display

Switched off
Bad connection
Low Battery

Switch on, Check display/ battery connection,
Change the battery

Reading erratic

Pressure on sensor
Radio transmission
Sensor old or faulty
Condensation on sensor.

Check flow, Move unit away, Change sensor, Dry in
air

Display segments missing

Display faulty

Return to dealer

Reading drifts

Rapid temperature change

Stabilize temperature & recalibrate

Will not calibrate

Sensor Malfunction

Contact Nuvair for repair or replacement

1L/min Flow

Restrictor/

Regulator
Assembly

10 PPM CO

Calibration Gas

Canister

Содержание Pro CO

























Результаты поиска

Содержание Pro CO

Отзывы:

Похожие инструкции для Pro CO

Бренды по названию

Популярные бренды

Nuvair Pro CO, Руководство пользователя

Результаты поиска

Содержание Pro CO

Отзывы:

Похожие инструкции для Pro CO

Бренды по названию

Популярные бренды