background image

Cautions 

 
1.

 

Before assemble the Noodle Molding into machine, put it into hot water for one minute. This 
can help the noodles come out much easier.   

2.

 

After continuous working of 3 times, the machine must stop and rest for 10 minutes.   

3.

 

While the noodles come out, if the paste is too dry, the motor will be overloaded in making 
the noodles. In this condition the motor will reverse and then stop working. Press “Cancel”, 
add  some  more  water  inside  and  start  mixing  the  flour  again,  then  replace  the  Noodle 
Molding. 

4.

 

If there is paste left inside the Noodle Molding, please wait until it’s dry, then strike it on a 
hard surface; the paste will drop off. If the paste is not dry yet, you can use a needle to clean 
it.   

5.

 

Below  parts  can  be  disassembled  for  cleaning: Mixing Tank,  Mixing  Axis,  Supporting  Board, 
Noodle Molding, Fasten Screw. The screw did not contact the flour so just use wet cloth to 
clean it. Never use a corrosive water to clean the machine body.   

6.

 

Before  disassemble  the  Mixing  Tank,  the  Mixing  Axis  must  be  disassembled  first.  When 
assemble the Mixing Axis, must make sure that it’s assembled well. 

7.

 

If  the  machine  is  damaged  or  cannot  operate,  please  don’t  open  the  machine.  Ask  a 
technician to check it.   

8.

 

During working, there cannot be any hard objects inside the Mixing Tank.   

9.

 

No matter if you disassemble, assemble or replace the parts, the electricity must be cut off. 
During  cleaning,  please  unplug  the  machine.  Besides  the  Mixing  Tank,  Mixing  Axis, 
Supporting Board, Noodle Molding and Measuring Cup, no other parts can be put into water.   

10.

 

If you want to open the Lid Cover while it’s running, please press the “Cancel” button to stop 
the machine.   

11.

 

If the weather is dry or rainy, please don’t use this machine outside of the house. 

12.

 

This machine cannot be used by children or young adults without supervision. 

13.

 

If the soft power cord is damage, it must be repaired or replaced by an authorized technician.   

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание PKPM350











Отзывы: