www.NutrichefKitchen.com
www.NutrichefKitchen.com
PART THREE: TROUBLE SHOOTING GUIDE
1. Faucet Leakage:
Solution:
Please screw out and remove the faucet and
install again, make sure the faucet matches the connection
of spear tightly.
2. SpearCross-bar Leakage:
Solution:
There is a nut under spear main body, tighten the
nut to prevent leakage.
3. Too Much Foam:
Solution:
Flow-control block would help to reduce the
speed of beer flowing and reduce amount of foam.
If there is too much pressure, please pull on the pressure
relieving ring for a couple of seconds.
When pressure within keg reach 30PSI, the pressure
relieving ring would release C02 automatically to keep safe.
4. C02 Leakage:
C02 capsule should be installed properly and
tightly.
In case there is C02 leakage, please observe the
position of leakage and continue with the tightening
process, but never screw out if gas remains.
PART FOUR: WARNING
1. Keep away from children under 18.
2. Never point cylinder towards someone's face.
3. Do not heat over 140°F as rupture may occur!
4. Discontinue using of this equipment if unsolvable leakage
or visible damage is found.
5. Capsule end become punctured when turned into
regulator base. Unscrewing capsule before it's empty can
result in loss of high pressure gas. Please remember, never
unscrew the C02 capsule before gas used up, liquid C02
spray onto unprotected skin may cause freezing burns.
6. Exterior of capsule may become frozen when in use, this is
normal. But don't touch with bare hands, your fingers
could stick to the frozen surface and cause frostbite.
7. Please ship via land or sea shipment, never bring C02
capsule when you travel by air.
Features
•
Complete Stainless Steel Mini Keg System
•
CO2 System Keeps Homebrew Fresh & Carbonated All Day
•
Solid Stainless Steel Construction Keep Beverage Colder Longer
•
Made of Food Grade S/S 304 Rust Proof Stainless Steel
•
With Neoprene Sleeve
•
CO2 Safety Pressure: 30 PSI
PKBRTP50
64 Oz Stainless Steel Complete Set Dispenser & CO2 System
Weight: 4.1 lbs.
Dimesions: 13.4 x 7.5 x 6.9 inches
PKBRTP100
128 Oz Stainless Steel Complete Set Dispenser & CO2 System
Weight: 4.80 lbs.
Dimesions: 19.5 x 7.5x 6.9 inches
3. Pull on the pressure relieving ring for a
couple of seconds. If the keg was
shaken in transit or warmed, it may
contain excessive pressure which must
be relieved before tapping. A hissing
noise is expected.
4. Slowly turn the regulator knob in
clockwise direction to 5 PSI, and stop
for 2 seconds and turn off regulator.
Wait for 2 mins, then pull on the pressure relieving ring
for a couple of seconds. This is for adjusting pressure of
keg beer.
5. Put a glass or pitcher under the faucet spout,with the
faucet knob pulled forward (ON), slowly turn the regulator
knob on in clockwise direction, until beer starts to flow
out. Don't continue adding pressure,suggest tapping 5-8
PSI(max pressure 30PSI), so please stop turning the
regulator knob when the pressure is enough to tap beer
out with perfect foam. Too much pressure would cause
over foam. When the beer stopped or flow slower, try
turning the regulator knob on slowly, to get bigger
pressure.
6. When you finish tapping, please turn regulator knob to
OFF position.
7. If no beer flow out,then the C02 capsule needs to be
replaced, unless no beer is rema ined. (Normally,16g
capsule can tap 4-5 liters of beer).
Caution:
Removing a punctured capsule from regulator
should be done slowly. Swish is expected if pressure
remains.
8. Turn the regulator knob off
and install a new capsule into
the regulator by following
above steps
