4
If using the Spiralizer disc
attachment:
Align the
notches on the
Spiralizer
Disc
with the tabs that are
located inside the
Work Bowl
towards the top. Once the
disc is properly seated on the
Blade Adaptor
and inside
of the
Work Bowl
, turn the
Spiralizer Disc
so that the
'FRONT'
is aligned with the
front of the
Motor Base
. The
spiralizer part of the disc will
sit directly under the
Feed
Chute.
CAUTION:
Never run the motor
with more than 1 blade attached.
3c If using the Spiralizer disc
1
Place the
Work Bowl,
with the
Chopping Blade
attached, on a clean,
dry, flat surface like a
countertop. Refer to the
assembly instructions
on page 12 for how to
properly attach the
Chopping Blade.
2
Prepare food (cut into
smaller pieces, remove
seeds, etc.) and place into
the
Work Bowl.
Do not
overload bowl with food.
If you are using liquid
ingredients do not fill past
the
LIQUID MAX
line.
NOTE:
Make sure the
Chopping
Blade
has been attached to the
Work Bowl BEFORE
adding
food to the bowl.
Using the chopping blade.
The
Chopping Blade
is a versatile blade that can be
used to chop, mix, mince, or purée foods.
3a If using the Chopping Blade
2 Prepare food (cut into smaller pieces, remove seeds, etc.)
3b If using a Slice/Shred
thin/thic
k shred disc
3b
If using a Slice/Shred disc
attachment:
The disc
attachments can be placed
in 2 different positions on the
Blade Adaptor.
The lower
position is for storage, and
the higher position is for use.
Hold the center knob of the
disc, and carefully place it on
the
Blade Adaptor.
Align the
markings on the disc
with the markings on the
Blade Adaptor,
so that the
lines connect. If the disc
appears to be in the lower
position, remove the disc and
rotate until the markings line
up and the disc sits in the
higher position.
CAUTION:
Blades are sharp!
Handle carefully. Keep fingers
away from the blade’s sharp
edges. Always hold blades by
grasping the plastic areas.
4
Place the
Work Bowl,
with
lid attached, onto the
Motor Base.
Turn the bowl
clockwise to lock into place.
You should hear a click when
the bowl is properly locked
into place.
3
Place the
Work Bowl Lid
on top of the
Work Bowl
.
Turn the lid clockwise, lining
up the arrows on the lid and
handle, to lock into place.
Place the
Dual-Size Food
Pusher
into the
Feed Chute.
NOTE:
The motor will not run
unless the lid is locked into place.
5b
If you need to add liquid
while processing, unlock
the
Inner Pusher
by
turning the
Pusher Cap
clockwise. Once unlocked, lift
the
Inner Pusher
and drizzle
liquid through the narrow
chute.
NOTE:
Do not fill liquid
ingredients past the
LIQUID
MAX
line.
5a
Plug in the unit, then press
your desired speed to
start processing food. The
blue light will illuminate over
the speed that is currently
running.
HIGH
PULSE
OFF
LOW
OFF
LOW
HIGH
PULSE
Before first use.
Before using your nutribullet
®
Food
Processor for the first time, please take a
moment to perform the steps below.
1. UNPACK
Open box. Remove the
Motor Base
and all
attachments. Place all parts on a flat, dry
surface.
2. CLEAN
Rinse all detachable parts and accessories. All
parts except the
Motor Base
are dishwasher
safe, or can be cleaned by rinsing with warm,
soapy water. Clean the
Motor Base
with a
clean, damp cloth.
WARNING:
Never submerge the
Motor Base
in wa-
ter or any other liquid. See Care
& Maintenance instructions on page 22 for more
detailed cleaning instructions.
1
Place the
Work Bowl
on a
clean, dry, flat surface, like a
countertop or table.
Assembly.
Review all warning and caution statements in the
Important Safeguards section (pages 2-5) and
above before proceeding to Step 1.
Assembly & use.
The nutribullet
®
Food Processor features a multi-
speed control panel for all types of food prep.
Control panel.
OFF:
Stops the Food Processor when operating on
continuous LOW or HIGH speeds.
HIGH:
Continuous HIGH-speed chopping or mixing.
PULSE:
A burst of chopping or mixing that runs at HIGH
speed. PULSE must be held to activate; motion will
stop when the button is released.
LOW:
Continuous LOW-speed chopping or mixing.
LOW
HIGH
PULSE
OFF
LOW
HIGH
PULSE
OFF
LOW
HIGH
PULSE
OFF
LOW
HIGH
PULSE
OFF
2
Place the
Blade Adaptor
in
the
Work Bowl.
Lower the
Blade Adaptor
onto the top
of the shaft located in the
center of the
Work Bowl.
Push down so the adaptor is
firmly and securely in place.
7-cup work bowl
place the blade adaptor in the work bowl
3a If using the Chopping Blade
3a
If using the Chopping Blade
or Dough Blade
: Hold the
plastic center of the blade,
and carefully place it on
top of the
Blade Adaptor.
Slide the blade down until
it reaches the bottom of the
Work Bowl.
Press it down
firmly to set it in place.
7
6
