![background image](http://html.mh-extra.com/html/nutool/nag115/nag115_original-instructions-manual_1719265015.webp)
15
GB
supplied insert the pins into the holes on the disc clamping nut.
Turn the wrench anti-clockwise to release the disc clamping nut.
If the disc backing washer is removed it must be replaced the
correct way round. The correct way to fit this onto the shaft can
be seen in Pic.5.
NOTE:
There are different types of discs used for different
applications. Select the correct one for the work being done.
Make sure the disc backing washer flats are located correctly
with the flats on the shaft. The grinding disc should be placed
onto the Angle Grinder with the writing facing upwards.
INSTALLING A NEW DISC (PICS. 6 & 7)
Place the disc over the shaft locating it onto the disc backing
washer. It can be seen that the backing washer has a raised lip.
The hole in the disc should match the diameter of the raised lip,
keeping the disc mounted central (Pic.6) Refit the disc clamping
nut (Pic.6). Tighten with fingers until the disc is clamped. Locate
and depress the spindle lock and using the supplied wrench,
(Pic.7) tighten the locking washer in a clockwise direction until
the disc is firmly clamped but do not over tighten. Release the
spindle lock and turn the Angle Grinder over.
The side handle can be fitted to either side of the machine to
suit the operator (Pic.8) ensure that the side handle is secured
but do not over tighten.
Connect the Angle Grinder to a suitable mains supply socket. It
is advisable to use an approved Residual current device (RCD).
If in doubt consult an approved electrician.
FOR YOUR SAFETY PLEASE FOLLOW THE THESE
INSTRUCTIONS
Working with an Angle Grinder should always be done in a
suitable designated work area for safety reasons. Hot sparks
are generated when grinding. Any debris nearby could be
ignited resulting in a fire. Read all the safety instructions before
using the Angle Grinder.
START/STOP AND ADJUSTMENT OF THE POSITION
OF THE REAR GRIP (PHOTO 9.1 & 9.2).
This tool is fitted with a safety device that prevents accidental
activation. To start the tool:
9.1) Press down without releasing.
9.2) Push the button forward and then press it down to make
the button be locked.
The button may be released while you are using the angle
grinder.
Press the button backward to switch off the tool.
If the machine makes an unfamiliar sound or vibrates excessively
switch it off immediately and disconnect from the power supply.
Investigate the cause or consult a service centre for advice.
Pic.10 shows a typical grinding operation.
NOTE:
The guard has been positioned to deflect hot sparks
away from operator. Grinding operations should be done with
the disc at an angle of between 30° and 40° to the work piece
(Pic.10).
During use it is advisable to periodically check the security of
the disc clamping nut, side handle and disc guard.
Be aware that grinding metal can cause harmful dust particles
that will damage your respiratory system and it is advised that
an approved dust mask is obtained from a reputable dealer.
NEVER immerse the grinding disc into any type of lubricant
including water. The Angle Grinder is a dry grinder. Failure to
observe will result in a fatal electric shock.
The guard is adjustable for different types of work. The picture
10 shows how the guard has been adjusted to deflect the
sparks away from the operators eyes. See safety instructions
for additional protective equipment.
Always keep mains power lead to the rear of the work being
grind.
The sound intensity level for the operator may exceed 85 dB(A).
Suitable ear protection must be worn by the operator.
TECHNICAL SPECIFICATION
NAG115
Voltage
230 V - 50 Hz
Motor
500 W
No load speed
11000 min
-1
Disc size
115mm M14
Sound Pressure Level
LpA 85,4 dB(A)
Sound Power Level
LwA 96,4 dB(A)
Vibration Level
4,38 m/s
2
Weight
2 kg
TECHNICAL SPECIFICATION
NAG125
Voltage
230 V - 50 Hz
Motor
860 W
No load speed
11000 min
-1
Disc size
125 mm M14
Sound Pressure Level
LpA 89 dB(A)
Sound Power Level
LwA 100 dB(A)
Vibration Level
4,42 m/s
2
Weight
2,1 kg
Содержание NAG115
Страница 5: ...5 1 8 8 2 5 5 2 2 9 1 1 3 3 4 4 NAG125 NAG115 6 6 7 7 ...
Страница 6: ...6 5 6 7 8 9 1 10 30 40 9 2 3 9 1 9 2 ...
Страница 109: ...109 ...