background image

 

OPERATION MANUAL 

FLEXESERVE HUB®

 

 

 

FLEXESERVE® | Operation Manual Flexeserve Hub® North America | V1 MAR 2021 | 40003230 

Page | 17 of 22 

Operation 

 

 

WARNING 

Only if the operator has been trained and is skilled in the operation of the equipment 

covered in this guide should this information be followed. 

 

Do NOT attempt to cook products in the equipment. 

 

Do NOT place anything heavier than 44Ibs (20kg) on to the display surface.

 

 

The equipment will only maintain the temperature of products that have initially been cooked, prior to 

display.  Ensure  that  food is  transferred  to  the  display  area  immediately  after  cooking  in  appropriate 

containers or packaging. 

 

Ensure that temperatures of the displayed products are checked and recorded on a regular basis, in 

accordance with local regulations. 

 

The temperature of the unit is displayed by the controller and is for indication of operating temperature 

only. Do NOT use this as a reference to core temperature of foods on display; regular temperature probing 

of the product is to be performed. A supplemental temperature gauge is fitted to the back panel. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The minimum and maximum set-point values have been pre-set in the factory to prevent the equipment 

holding temperatures from being adjusted beyond legal and safety limits. These can only be adjusted by 

a Flexeserve® appointed engineer. 

 

To view the set temperature of the unit, press the ‘temperature’ button for half a second, and then release. 

 

To change the temperature of the unit, press and hold the ‘temperature’ button and press the arrow 

buttons to increase (

) or decrease (

) the temperature. When the ‘temperature’ button is released, the 

new value is stored. After the temperature has been set, the display will revert back to the operating 

temperature, which will rise or fall as it reaches the set temperature. 

 

Flexeserve Hub® is manufactured to comply with health and safety regulations, and has been tested and 

certified to NSF standards. You must operate the equipment properly using only calibrated temperature 

probes to ensure food is thoroughly cooked to the safe standards according to local regulations. 

 

Temperature 

adjust 

Temperature 

button 

Содержание Flexeserve Hub 1000

























Отзывы: