background image

ONE YEAR LIMITED WARRANTY:

IF YOU WOULD LIKE TO ORDER REPLACEMENT 

OR MISSING PARTS. PLEASE VISIT US AT:

WWW.NURSERYWORKS.NET

OR YOU CAN CONTACT US BY MAIL:

Registering your product is even easier than 

before. You can register your product on our 

website at : www.nurseryworks.net

PO BOX 296, Earlwood, NSW 2206, Australia 

ABN:73 131 269 988

Tel: 02 8064 2305

Fax: 02 8456 6020

7

We will replace any missing parts at the time 

of purchase or any defective item within a 

one year period from the date of original purchase. 

Please keep your receipt so that we may process 

your warranty request. This warranty only 

covers new units with original packaging and 

ownership, and is not transferable. It does not 

cover any used, secondhand or demo 

models. 

This warranty does not cover any damaged 

or defective parts that result from installation 

and assembly, normal wear and tear, abuse, 

negligence, improper use or alteration to the 

finish, design, and hardware of the cot. The 

specific legal rights of this warranty may vary 

from state to state. Some states do not allow 

any exclusion or limitation of incidental damages. 

Some States do not allow limitation on how 

long an implied warranty lasts.    

 

Содержание Loom Cot





















Отзывы: