5.
Track Cue
–
Sets and recalls the main Cue point in the current track.
Hold down the CUE button for
temporary play of the cue point. The track will play for as long as the button is held down and return
to the cue point once it is released. Hold
Shift + Cue
to return to the start of the loaded track.
6.
Sync
–
When enabled allows BPM syncing between decks for the software tracks.
7.
Play/Pause
–
Starts and suspends playback.
8.
Stutter
–
Press this button while the music is playing to jump back to the last set cue point, creating a
"stutter" effect.
9.
Cue (PFL)
–
Sends pre-fader audio to the Cue Channel for head phone monitoring. Hold
Shift + Cue
(PFL)
to activate FX 1 on Deck A, and FX 2 on Deck B.
10.
Platter/Jog Wheel
–
This capacitive, touch-sensitive jog wheel controls the audio when the wheel is
touched and moved. When the Scratch button is not active and the track is stopped, use the wheel to
quickly scrub through the track. When the Scratch button is active, use the wheel to grab and move
the audio, "scratching" the track as you would with a vinyl record. You can also grab the non-touch-
sensitive outer wheel to bend the pitch of the track.
11.
Scratch
–
When active, the platter will have the ability to scratch.
12.
Pitch Fader
–
Controls the tempo (speed) of the individual decks.
13.
Pitch Bend Down
–
Press and hold to
momentarily reduce the speed of the track. Hold
Shift +
Pitch bend down
to engage Key Lock.
14.
Pitch Bend Up
–
Press and hold to momentarily increase the speed of the track. Hold
Shift + Pitch
bend up
to change the range of the pitch fader.
15.
FX Knob 1
–
This will adjust the Effect Unit Wet/Dry of the FX Unit.
16.
FX Knob 2
–
In Single FX mode this knob will control the 1
st
FX parameter, in multi FX mode this
knob will adjust the 1
st
effect in the chain. Hold
Shift + FX Control
to select the effect for FX slot 1.
17.
FX Knob 3
–
In Single FX mode this knob will control the 2
nd
FX parameter, in multi FX mode this
knob will adjust the 2
nd
effect in the chain. Hold
Shift + FX Control
to select the effect for FX slot 2.
18.
Beats Knob (FX 4)
–
In Single FX mode this knob will control the 3
rd
FX parameter, in multi FX mode
this knob will adjust the 3
rd
effect in the chain. Hold
Shift + FX Control
to select the effect for FX slot
3.
19.
FX 1 Button
–
When in Single FX mode, this button will turn on FX unit 1, in Multi FX Mode this
button has no function. Hold
Shift + FX1
to set and start playback of a 1-beat autoloop.
20.
FX2 Button
–
When in Single FX mode, this button trigger the 1
st
effect button, in Multi FX Mode this
button turns FX 1 slot on and off. Hold
Shift + FX2
to set and start playback of a 2-beat autoloop.
21.
FX3 Button
–
When in Single FX mode, this button trigger the 2
nd
effect button, in Multi FX Mode this
button turns FX 2 slot on and off. Hold
Shift + FX3
to set and start playback of a 4-beat autoloop.
22.
Tap Button
–
When in Single FX mode, this button trigger the 3
rd
effect button, in Multi FX Mode this
button turns FX 3 slot on and off. Hold
Shift + Tap
to
set and start playback of a 16-beat autoloop.
23.
Loop In
–
Press this pad to set the beginning of a loop when in Looping Mode. After a Loop Out point
is set and this button is pressed again, it will allow for fine adjustment of the Loop In point. Pressing
Shift + Loop In
will set the current Pad Mode as “Looping Mode”. See the PAD MODE COMMANDS
section for information on this pad’s additional functions.
24.
Loop Out
–
Press this pad to set the end of a loop when in Looping Mode. When this button is
pressed again after a Loop Out point has been set, it will allow for fine adjustment of the Loop Out
point. Pressing
Shift + Loop Out
will set the current pad mode to “Sample (S)” Mode. See the PAD
MODE COMMANDS section for information on this pad’s additional functions.
25.
Reloop
–
Press this pad when inside a loop to turn the loop off. When this button is pressed again
outside a loop, this will activate the loop and start playback from its Loop In point. If a loop has not
been set, this button will have no effect. Pressing
Shift + Reloop
will set the current pad mode to
“Hot Cue Mode”. See the PAD MODE COMMANDS section for information on this pad’s additional
functions.
26.
Loop x1/2
–
Press this pad to reduce the currently playing loop length by half when in Looping Mode.
If a loop is not playing, this will set the autoloop length. Hold
Shift + Loop 1/2
to double the loop
length. See the PAD MODE COMMANDS section for information on this pad’s additional functions.
27.
Channel Volume
–
Adjusts the volume of the individual channels in the software.
28.
Master Volume
–
Adjusts the volume of the master mix coming from the software.
Note:
This does not affect the microphone volume. Use the Mic Gain knob to control the microphone
volume.
