Numark iCDMIX 2 Скачать руководство пользователя страница 23

Страница: 23 / 23

TROUBLESHOOTING

PAGE 22

TROUBLESHOOTING

Mixer does not turn on.

Disconnected Power Cord?

Connect Power Cord.
See INPUTS AND OUTPUTS,

pages 15-16

See INPUTS AND OUTPUTS,

pages 15-16

The sound level is very low.

The Input Selector Switch is in the

wrong position.

Select the device that is playing

with the input selector switch.
See CONTROLS, page 7

See CONTROLS, page 7

See CONTROLS, page 11

See CONTROLS, page 13

The component is connected to the

wrong input terminal or channel.

Connect the input to the correct

channel using the Set-Up Diagram.
See SETUP DIAGRAM, page 4

See INPUTS AND OUTPUTS,

pages 15-16

See SETUP DIAGRAM, page 4

The main output device is

connected to the Recording Level

Output.

Connect the output device to the

Master Output.

Problem

Cause?

Solution

The output sound is very distorted.

The Input Trims are set too high.

Adjust the Input Trims so that they

average 0db on the LED display.

The Master Volume is set too high.

Adjust the Master Volume so that

0db is averaged on the LED display.

The Crossfader does not work.

NOTE:

Static electricity and/or other external interference may cause this unit to malfunction. To reset the unit to it's

normal condition, turn the power off and then on again. If the problem continues to persist, refer to the

connected component's troubleshooting guides. If the problem is not resolved after checking these items,

contact the nearest authorized Numark dealer.

The Crossfader Reverse Toggle is in

the wrong position.

Set the Crossfader Reverse Toggle

to the opposite direction.

The Output sound exhibits

excessive hum or buzzing.

The Turntable Grounding wires are

not connected.

Connect the Turntable Ground

wires to their respective Grounding

Lug.

Содержание iCDMIX 2
























Результаты поиска

Содержание iCDMIX 2

Отзывы:

Бренды по названию

Популярные бренды

Numark iCDMIX 2, Руководство по эксплуатации

Результаты поиска

Содержание iCDMIX 2

Отзывы:

Бренды по названию

Популярные бренды