manualshive.com logo in svg

Numark iCDMIX 2, Руководство по эксплуатации

Поделиться
Скачать
Numark iCDMIX 2 Скачать руководство пользователя страница 19

PAGE 18

CUSTO SERVICING YOUR MIXER

Replacing the Crossfader

Customizing the Direction of the Input Selector Switches

1. After removing the top panel, remove the

two screws that secure the selector switch
you want to rotate using a #2 Philips
Screwdriver.

1. After removing the top panel, remove the

two screws that secure the crossfader
using a #2 Philips Screwdriver.

2. Carefully slide the crossfader out of the

mixer chassis, and unplug the harness
from the bottom of the part. Replace the
crossfader, refasten the two screws that
hold the crossfader in place.

3. Resecure the top panel, test the function,

and refasten the four screws that secure
the top panel.

2. Carefully slide the switch out of the

mixer chassis, and unplug the harness
from the bottom of the part. Rotate and
replace the switch, refasten the two screws
that hold the switches in place.

3. Resecure the top panel, test the function,

and refasten the four screws that secure
the top panel.

Содержание iCDMIX 2
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды