Numa Patriot RC50 Скачать руководство пользователя страница 4

04/23/10

MANUFACTURER OF DOWN HOLE HAMMERS AND BITS

WARRANTIES AND REMEDIES

LIMITED WARRANTY

 

 

Numa warrants that the Product will be new and free from defects in material and workmanship 

under normal use as contemplated by this Contract for a period of six (6) months from the date of 

shipment.

 

Except for the foregoing warranty, Numa disclaims all warranties and representations wherever 

made, including warranties of merchantability, durability, length of service, or fitness for a particular 

purpose.

 

Any alteration or modification of the original product without the express written consent of 

Numa will void this warranty.

REMEDY

 

If,  during  such  warranty  period,  Buyer  promptly  notifies  Numa  in  writing  of  any  defect  and 

establishes that the above warranty is not met, Numa shall either repair or replace the Product or 

credit the customer, as it deems necessary to meet the warranty.

 

Such repair, replacement, or credit of Product shall constitute complete fulfillment of Numa's 

obligation under this warranty, and upon the expiration of the original warranty period, all of Numa's 

obligations hereunder shall terminate.  

LIMITATION OF LIABILITY

 

 

Numa shall not be liable to Buyer whether in contract, in tort (including negligence and strict 

liability), under any warranty or otherwise, for any special, indirect, incidental or consequential loss 

or damage whatsoever, including (without limitation) loss arising from delay, cost or capital and loss 

of profits or revenues.  The remedies set forth in this Contract are exclusive, and the total cumulative 

liability of Numa under this Contract or for any act or omission in connection therewith or related 

thereto, whether in contract, in tort (including negligence and strict liability), under any warranty or 

otherwise, is limited to the price paid by Buyer for the Product.

The 

WARNINGS

CAUTIONS

 and 

NOTES

 used throughout the text of this 

instruction book are defined as follows:

WARNING

 

A specific procedure or practice that must be strictly followed,  

 

 

or a specific condition that must be met, to prevent possible    

 

 

bodily harm.

CAUTION

 

A specific procedure or practice that must be strictly followed,  

 

 

or a specific condition that must be met, to prevent damage    

 

 

to the equipment.

NOTE

 

Important supplemental information.

Numa

®

,Champion

, and Patriot

 

 are registered trademarks of Numa.

Содержание Patriot RC50

























Отзывы: