Numa Champion 330 Скачать руководство пользователя страница 4

04/23/10

MANUFACTURER OF DOWN HOLE HAMMERS AND BITS

WARRANTIES AND REMEDIES

LIMITED WARRANTY

Numa warrants that the Product will be new and free from defects in material and

workmanship under normal use as contemplated by this Contract for a period of six (6) months from

the date of shipment.

Except for the foregoing warranty, Numa disclaims all warranties and representations wherever

made, including warranties of merchantability, durability, length of service, or fitness for a particular

purpose.

Any alteration or modification of the original product without the express written consent of

Numa will void this warranty.

REMEDY

If, during such warranty period, Buyer promptly notifies Numa in writing of any defect and

establishes that the above warranty is not met, Numa shall either repair or replace the Product or

credit the customer, as it deems necessary to meet the warranty.

Such repair, replacement, or credit of Product shall constitute complete fulfillment of Numa's

obligation under this warranty, and upon the expiration of the original warranty period, all of

Numa's obligations hereunder shall terminate.

LIMITATION OF LIABILITY

Numa shall not be liable to Buyer whether in contract, in tort (including negligence and

strict liability), under any warranty or otherwise, for any special, indirect, incidental or consequential

loss or damage whatsoever, including (without limitation) loss arising from delay, cost or capital

and loss of profits or revenues.  The remedies set forth in this Contract are exclusive, and the total

cumulative liability of Numa under this Contract or for any act or omission in connection therewith

or related thereto, whether in contract, in tort (including negligence and strict liability), under any

warranty or otherwise, is limited to the price paid by Buyer for the Product.

The 

WARNINGS

CAUTIONS

 and 

NOTES

 used throughout the text of this

instruction book are defined as follows:

WARNING

A specific procedure or practice that must be strictly followed,
or a specific condition that must be met, to prevent possible

bodily harm.

CAUTION

A specific procedure or practice that must be strictly followed,
or a specific condition that must be met, to prevent damage to

the equipment.

NOTE

Important supplemental information.

Numa

®

,Champion

®

®

®

®

®

, and Patriot

® 

® 

® 

® 

® 

 are registered trademarks of Numa.

Содержание Champion 330



























Отзывы: