Numa Champion 330 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 26

Numa Champion 330 Скачать руководство пользователя страница 20

Page 16

Champion

®

®

®

®

®

330

MANUFACTURER OF DOWN HOLE HAMMERS AND BITS

05/12/17

SECTION V

LUBRICATION

The Champion 330 hammer requires a continuous supply of the correct type of Rock Drill

Oil. The Champion 330 hammer consumes at least 20 quarts (19 litres) of Rock Drill Oil per hour

in order to maintain adequate lubrication. See table 5-1 for recommended Rock Drill Oil.

Medium SAE 30

Heavy SAE 50

Shell

Air Tool Oil S2 A 150

Air Tool Oil S2 A 320

Texaco / Caltex

Rock Drill Lube 100

Rock Drill Lube 320

Chevron

Vistac 150

Vistac 320

Conoco

Conoco 150

Conoco 320

Numa Bio Blend

RDP 150

RDP 320

Table 5-1

Recommended Rock Drill Oil

CAUTION

ROCK DRILL OILS ARE THE ONLY ACCEPTABLE LUBRICANTS. SAE 50 ROCK

DRILL OIL SHOULD BE USED IN AMBIENT TEMPERATURES OF 80° FAHRENHEIT

(27° CELSIUS) OR HIGHER. CONTACT NUMA FOR ACCEPTANCE OF

ALTERNATIVE ROCK DRILL LUBRICANTS.

CAUTION

THE CHAMPION 330 HAMMER, AS WITH ANY MACHINE, REQUIRES

CONTINUOUS LUBRICATION. THE FAILURE TO SUPPLY ADEQUATE

LUBRICATION TO THE HAMMER CAN CAUSE PREMATURE FAILURE AND MAY

VOID THE WARRANTY.

«
...
18
19
20
21
22
...
»

Содержание Champion 330



























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды