background image

XBOXER 

Run Around Coil

Installation, Operating and
Maintenance Instructions

OPTIONS AVAILABLE

The EMC Directive 

2004/108/EC  

The Low Voltage 

directive 

2006/95/EC

This document refers to the following

Nuaire Run Around Coil products:

Please note - project specific variations of these products may be

supplied. 

Such products will be identified on the unit rating plate by the 

reference – Qaxxxx. 

Generally, the standard product information given here will apply,

and any additional information necessary for the safe installation,

operation and maintenance of the product will be supplied directly

to the contractor.

Unit overall dimensions (mm)

Unit Code

A

B

Duct size D x E

R4-RAC-L/N/NC

2800

1600

1600

1540 x 740

R5-RAC-L/N/NC

3200

2000

2000

1940 x 940

R6-RAC-L/N/NC

3800

2600

2600

2540 x 1240

N.B If CW or DX modules are included add 600mm to overall length.

Nuaire Limited

Western Industrial Estate  Caerphilly  United Kingdom  CF83 1NA  

T: 029 2085 8400  F: 029 2085 8444  E: [email protected]  W: www.nuaire.co.uk

1

17. 06. 15. Leaflet Number 671424

AHU with Heat Recovery section and direct drive AC motor technology.

Figure 2. Model shown: R4/6-RAC-N (No heater). Includes Ecosmart control.

Figure 1. Model shown: R4/6-RAC-L (LPHW). Includes Ecosmart control.

Figure 3. Model shown: R4/6NC-RAC-L (LPHW). No Ecosmart control.

Figure 4. Model shown: R4/6NC-RAC-N (No heater). No Ecosmart control.

Intake

Discharge

Supply

Extract

Code description example

1. = 

Type/Curve Ref. 

2. =  Ecosmart control as standard

NC = No control

3. =  Run around coil

4. =  Unit type

L  = LPHW

N = No heater

5. =  2 row coil or 3 = 3 row coil

6. =  Optional Weather Roof

R4NC - RAC - L 2 WP

| |

|

| |

|

1

2

3

4 5

6

A

B

C

D

E

Note: Full length access is from either side.

1600mm for Run Around Coil maintenance.

800mm for filter access etc.

1600mm -

Run Around Coil

maintenance.

800mm -

filter access etc.

Содержание XBOXER R4-RAC-L













Отзывы: