-1-
-10-
Im por ta nt-Sa fe ty Pr e c a utions
To prevent fire or shock hazard, do not expose this device to rain or moisture.
Does not use near a bathtub, washbowl, kitchen sink, or laundry tub,
in a wet basement, or near a swimming pool.
■ To avoid electrical shock, do not open this device.
■ This device should be operated to use only the power supply included with it
or provided as an accessory.
■ Do not overload wall outlets and extension cords as this can result in the risk
of fire or electrical shock.
■ Do not attempt to service this device yourself. Refer servicing to qualified
personnel only.
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
■ Consult the dealer or an experienced radio/TV technician for help.
■
Note:
This equipment has been tested and found to comply with Part 15 of the FCC
Rules, or R&TTE CE directive. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy, if not installed and used
in accordance with the instruction, it may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
H.Use Notes
1.
Be sure the transmitter and the receiver were connected to the equipment
correctly (e.g. Connect the transmitter to the camera, and the receiver to the TV or
DVR).
2.
When DC plug is pulled out from transmitter or receiver or wireless
camera, it needs to wait for a few seconds to insert it again.
3.
Adjust antenna to decrease interference. (vertical or horizontal)
4.
In most situations, one pair has a better distance up to 800 meter (open site).
When two pairs or more used at the same time, can automatically jump to
different channels, but the distance between pairs, preferably greater than 2 meters far.
5. If there are some reasons cause the devise stop, you can try to turn off the power
then on again and make the devise re-link(re-pairing)
6.
It is suggested to have 10 pairs mostly operated in same location, but the
pairing can not be at the same time.
7. When use IR extender (option), it is normal when response slow in the receiver
side (RX) by remote control, please don't click the remote control keys too
quick.
I.Troubleshooting
Notice: The change or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements,
no change to the antenna or the device is permitted. Any
change to the antenna or the device could result in the
device exceeding the RF exposure requirement and void
user's authority to operate the device.
Problems
Possible Solution
Monitor(RX) shows
“No Video Signal”
Wireless Camera CCD bad, or no video input from TX(wired
camera, DVD power off or stolen, cable disconnected or
damaged), please check and make it right
Monitor(RX) shows
“No Signal”
Wireless camera or TX power off; wireless camera or TX vs RX
distance is too long, so that transmission signal is weak, please
check and make it right
No picture or sound
Check all cable connections
Make sure power plugs are pushed all the way in
Check power switches on the remote TV or DVR and
Video source (Camera, Camcorder, etc.)
Check if the POWER LED of the transmitter/digital wireless
camera and receiver is lighting or not? Their LINK LED should be lit
If Their LINK LED should not be lit, you must re-pair their
codes following the D. instruction of the manual
Interference:
picture or audio
Adjust receiver and transmitter/digital wireless camera antenna
orientation
Try to place transmitter/digital wireless camera and receiver in a
more close-in location
If using a microwave oven, turn it off.
Remove microwave oven or wireless router from the path between
transmitter/digital wireless camera and receiver
