NTP Technology Penta 720-800A Скачать руководство пользователя страница 2

Installation guide Penta 720-800A Base unit

 

 

 

Doc no. 720-8001-A-4 

Rev. date 131030 

Page 2 of 13 

 
 
 

 

 

WARNING

 – when using electric products, basic precautions should be followed, including the following: 

 

Read all of the safety and installations instructions and explanation of graphic symbols before using the 
product. 

 

1   Do not use this apparatus near water. 

6.   Clean only with dry cloth. 

7.   Do not block any ventilation openings. Install in 

accordance with the manufacturer's 
instructions. 

8.  Do not install near any heat sources such as 

radiators, heat registers, stoves, or other 
apparatus (including amplifiers) that produce 
heat. 

9.  Do not defeat the safety purpose of the 

polarized or grounding-110 to 125V type plug 
according to UL 817 and CSA C22.2 no. 42. A 
polarized plug has two blades with one wider 
than the other. A grounding type plug has two 
blades and a third grounding prong. The wide 
blade or the third prong are provided for your 
safety. If the provided plug does not fit into your 
outlet, consult an electrician for replacement of 
the obsolete outlet. 

 

 

10  Protect the power cord from being walked on 

or pinched particularly at plugs, convenience 
receptacles, and the point where they exit from 
the apparatus.  

11  Only use attachments/accessories specified by 

the manufacturer 

12. Use only with the cart, stand, tripod, bracket, or 

table specified by the manufacturer, or sold 
with the apparatus. When a cart is used, use 
caution when moving the cart/apparatus 
combination to avoid injury from tip-over. 

13  Unplug this apparatus during lightning storms 

or when unused for long periods of time. 

14  Refer all servicing to qualified service 

personnel. Servicing is required when the 
apparatus has been damaged in any way, such 
as power-supply cord or plug is damaged, 
liquid has been spilled or objects have fallen 
into the apparatus, the apparatus has been 
exposed to rain or moisture, does not operate 
normally, or has been dropped. 

 

DANGER

  

Improper connection of the equipment-grounding can result in a risk of electric shock. Do not modify 
the plug provided with the product – if it will not fit the outlet have a proper outlet installed by a qualified 
electrician. Do not use an adapter which defeats the function of the equipment-grounding conductor. If 
you are in doubt as to whether the product is properly grounded, check with a qualified serviceman or 
electrician. 

 

 

IMPORTANT SAFETY INSTRUCTIONS  

READ AND KEEP THESE INSTRUCTIONS

 

Содержание Penta 720-800A














Отзывы: