NSS CHARGER 2717 DB Скачать руководство пользователя страница 2

IMPORTANT SAFETY INSTRUCTIONS 

BATTERY POWERED EQUIPMENT WITH ON BOARD CHARGERS

WARNING:

Failure to observe these instructions can cause personal 

injury to machine operator or bystanders.

GENERAL

x

ALWAYS

 read and understand all instructions before 

installing or charging batteries. 

x

NEVER

attempt to install or charge batteries unless 

you have been trained to do so. 

x

NEVER

allow an untrained person to install or charge 

batteries. 

x

ALWAYS

remove all jewelry when working on or 

near the batteries. 

x

ALWAYS

turn off all switches during installation and 

service. 

x

ALWAYS

disconnect the battery leads before 

performing any service or repair. 

x

ALWAYS

 wear eye protection, rubber gloves and 

protective clothing to avoid contact with battery acid. 

x

NEVER

lay anything on top of batteries as arcing 

may occur. 

x

IF CONTACT WITH BATTERY ACID OCCURS

,

follow these instructions: 

x

 

SKIN – rinse area with water. 

x

 

EYES – Flush with water for 15 minutes. 

x

 

INTERNAL – Drink water or milk.  Follow with Milk 
of Magnesia, beaten egg or vegetable oil.  Call a 
physician immediately. 

BATTERY INSTALLATION  

x

ALWAYS

 use two people to install, as batteries are 

heavy.

x

ALWAYS

 turn off all machine switches. 

x

ALWAYS

 position batteries as shown on the 

machine installation decal to maintain machine 
balance. 

x

ALWAYS

 connect batteries as shown on the 

machine installation decal to avoid shorting out the 
batteries and the electrical system. 

BATTERY CHARGING 

x

ALWAYS

 read instructions on charger carefully. 

x

ALWAYS

 use the NSS supplied charger with proper 

voltage rating. 

For lead acid batteries only, (does not apply to gel 
cell or maintenance free batteries).

x

ALWAYS

 check to ensure the battery water level 

covers the battery plates before charging. 

x

ALWAYS

 check water level after charging and add 

water if necessary to bring level to the bottom of the 
fill hole. 

x

NEVER

 overfill batteries as 

battery and machine damage may 
result.

x

ALWAYS

 wipe any acid from the top of batteries 

using a soap solution. 

x

ALWAYS

study battery manufacturers’ specific 

precautions such as recommended rates of charge. 

x

ALWAYS

reattach caps to batteries.  Do not charge 

with caps loose or removed. 

x

ADD

 only distilled or treated city water.  Not well 

water.

x

NEVER

 charge a frozen battery.

x

ALWAYS

 plug the charger into an earthed socket-

outlet.

x

NEVER

 touch uninsulated portion of output connector 

or uninsulated battery terminal.

x

ALWAYS

 disconnect the AC supply before making or 

breaking the connections to the battery while 
charging. 

x

NEVER

 open or disassemble charger. 

x

NEVER

 operate charger if the AC supply cord is 

damaged or if the charger has received a sharp blow, 
been dropped, or otherwise damaged in any way. 

Read and understand all 
instructions before installing 
or charging batteries. 

No smoking, open 
flames, or sparks while 
working with batteries. 

Contains acid.  
Avoid contact 

Poison.  Causes 
severe burns.  Avoid 
contact.

WARNING:  

Batteries emit hydrogen

,

which can cause fire or explosion.

NEVER 

smoke, light a match, or cause a spark during operation or charging. 

ALWAYS

 charge in a well-ventilated area away from open flame.

ALL REPAIR SERVICE MUST BE PERFORMED BY AN NSS AUTHORIZED DISTRIBUTOR/ 
SERVICE STATION USING ONLY NSS ORIGINAL EQUIPMENT PARTS 

https://harrissupplyind.com - To Order Parts Call 608-268-8080

Содержание CHARGER 2717 DB













Отзывы: