background image

4. Mounting of the Foot Pedal 

(ULTIMATE XL-D)

Insert the foot pedal plug into the      Foot Pedal Connector at the back of the unit.

5. Mounting of the Air Turbine 

(Option)

Insert the plug of the Turbine Adapter into the 
     Turbine Adapter Connector at the back of the 
unit. Insert two hoses from the      Turbine Adapter 
into the openings for foot pedal connection in the air 
line kit. (Fig. 5)

1. Connect the power code to outlet.
2. Make sure that the      Speed Control Knob is at the lowest position (position reached by fully 

turning counterclockwise)

3. Turn the      Power Switch. The preset rotation speed will appear on the Indicator.
4. Select the rotation direction with      Forward/Reverse Selector Switch. Each time this switch 

is pressed, the direction changes between FORWARD and REVERSE.

5. Preset the maximum rotation speed with the      Speed Control Knob.
6. Depress the      Knee Controller for ULTIMATE XL-K and the      Pedal for ULTIMATE XL-D, 

and the motor will run. The rotation speed can be variably controlled within the preset 
maximum rotation speed range according to the degree of depression of the      Knee 
Controller or the      Pedal.

Auto cruise mechanism
To fix the speed within the rotation speed range set by the volume with the      Speed Control 
Knob, press the      Auto Cruise Switch while the motor is at rest. The display lamp, which is 
next to the switch, will light up. If the desired speed is set with the      Knee Controller or the 
     Pedal and a uniform speed can be maintained for one second, the motor will continue 
running at the desired speed if the      Knee Controller or the      Pedal is released. To cancel 
it, depress the      Knee Controller or the      Pedal again or press      Auto Cruise Switch 
again.

6

7

1. Mounting of the Unit

(1) ULTIMATE XL-K

Bore a hole while aligning the attached 
template with the inside of the right side of 
the technical desk. Then, mount a bracket 
with the attached screw and nut, and mount 
the unit by inserting the bracket lug into the 
opening at the back of the unit. (Fig. 1)

(2) ULTIMATE XL-D (Option)

ULTIMATE XL-D is used by standing it on a 
work bench, but it can be used by mounting 
it by use of the optional bracket if there is a 
wall at right side of the technical desk. If the 
unit is to be mounted on the bracket, remove 
the two cover-mounting screws. (Fig. 2)

2. Set up of Control Unit

Fig.1

Fig.2

2. Mounting of the Motor

Insert the motor cord plug locator into      Motor 
Connector aligning it with the groove of the 
connector, and tighten the motor cord plug nut 
to fix. (Fig. 3)

Fig.3

3. Connecting of the Power Cord

Securely insert the plug of Power Cord into 
connector at the back of the unit aligning it with 
the configuration. (Fig. 4)

Fig.4

7

5

6

5

5

7

5

5

6

6

6

6

7

9

3

3

10

10

12

17

13

Fig.6

OUT

IN

OUT

OUT

OUT

IN

AIR IN

To XL-K/D

Foot Pedal Connector

3. Operation Procedure

Fig.5

Turbine Adaptre

Connector

Foot Pedal

Connector

English

Содержание NE231












Отзывы: