background image

 
 
 
 
 
 
 
 
 

MIDI COMMANDS RECEIVED 

 
COMMAND 

  HEX 

CODE 

 DATA 

       

 
NOTE ON 

 

 

1001nnnn 

 

n = MIDI channel assignment 1-16 (0-15) 

 

 

 

 

0kkkkkkk 

 

k = Lighting channel no. (32-47, 64-79) 

    0vvvvvvv  v 

Lighting 

channel intensity (0 - 127) 

 
CONTROL 

 

 

1011nnnn 

 

n = MIDI channel assignment 1-16 (0-15) 

CHANGE 

 

 

0kkkkkkk 

 

k = Control number (see below) 

    0vvvvv-vv 

 v 

Control 

value 

(see 

below) 

PROGRAM 

 

 

1100nnnn 

 

n = MIDI channel assignment 1-16 (0-15) 

CHANGE 

 

 

0kkkkkkk 

 

k = Program number (see below) 

 
MIDI 

CLOCK 

  11111000 

 Real 

time 

msg 

 
SYSTEM 

  11110000 

 start 

of 

system 

exclusive 

EXCLUSIVE 

  11110111 

 end 

of 

system 

exclusive 

 

CONTROL CHANGES ACCEPTED 

 
CONTROL 

NUMBER 

 CONTROL 

VALUE 

 ACTION      

 

 

 

 

0 - 127   

(OOH - 7FH) 

Sets fade rate for proceeding light level changes 

 

 

 

 

0 - 127   

(OOH - 7FH) 

Sets relative chase rate  0 = stop, 127 = max 

 
60 

   0 

(OOH)   Deactivates 

chase. 

 

 

 

 

1 – 4    

(01H - 04H) 

Normal chase I – 4 

 
64 

   0 

 

 (OOH) 

 Reset 

console 

(if 

conf.) 

 
70 

   0 

 (OOH) 

 Direct 

Dimmer 

Access 

off 

 

 

 

 

 

(01H)   

Direct Dimmer Access on ignore note off cmds 

 

 

 

 

 

(02H)   

Direct Dimmer Access on note off cmds accepted 

 
123 

   0 

 (OOH) 

Reset 

console 

(if 

conf.) 

 
 

REAL TIME MSGS ACCEPTED 

 
MESSAGE 

  ACTION          

 
MIDI clock 

 

 

Syncronizes chase rate. 

Содержание NCM 6200




















Отзывы: