NRG Systems LOGR-S Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 73

background image

NRG Product Manual

LOGR-S Data Logger

NRG_LOGR-S_Manual
Rev. 1.0

[email protected] | Page 35

5 November 2021

Hukseflux SR30 Heater Control

This file can be placed on the FTP
server to control the heater of
the Hukseflux SR30 pyranometer.
As a default, the sensor fan is
always on. The ambient
temperature used for thee SR30
heater control must be a single
ended analog temperature
sensor (such as the NRG 110S or
NRG T60) and

must be wired to

Channel 14

. The SR30 controller

will turn the heater on/off based
on the value of the temperature
sensor and the control
temperature settings in the
command file.
This only values in this file that
should be

edited are the “on

temperature” which is the

temperature (in degrees C)
below which the SR30 heater

should turn on and “hysteresis”

which is the amount of
temperature lag (in degrees C)
for heater control. The other
parameters are registers and
values specific to the SR30 sensor
and should not be altered.

[command]

instruction = serial
sensor control

[control params]

heater coil = 1
fan coil = 3
temperature reg = 6
temperature reg count = 1
on temperature = 50
hysteresis = 5

*These command options are actionable via the webserver.

«
...
33
34
35
36
37
...
»

Содержание LOGR-S










































































Отзывы:

Нет отзывов

Похожие инструкции для LOGR-S

Бренд: PICO Страницы: 17

DL-300-WF Series

Бренд: ICP DAS USA Страницы: 4

Бренд: ALAT UJI Страницы: 25

Бренд: Metal Samples Company Страницы: 54

Бренд: LogTag Recorders Страницы: 46

CTD-Diver DI28 Series

Бренд: Van Essen Страницы: 34

Бренд: Sanav Страницы: 13

Бренд: Xylem Страницы: 50

Бренд: VOLTCRAFT Страницы: 27

Бренд: VOLTCRAFT Страницы: 116

Бренд: VOLTCRAFT Страницы: 100

VSN-MGR-CMML SERIES

Бренд: Power One Страницы: 25

Бренд: NOVAK Страницы: 35

Бренд: bmcm Страницы: 8

Бренд: Adcon Страницы: 43

Бренд: Agrowtek Страницы: 11

Бренд: Agrowtek Страницы: 22

CAMRegis AKO-15740

Бренд: AKO Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды