NPower 35013 Скачать руководство пользователя страница 9

CHARGING NPOWER POWERPACK AND JUMPSTARTER        

This charger is capable for charging Npower powerpack and jump starter (item# 457501, 
457801, 457102, 457402, 24928, 27941, and 39616). When chargin a Npower unit, simply 
plug the barrel plug into unit’s charging jack, please refer below picture. 

1 AMP CHARGE RATE

This charger is recommended for charging small batteries such as those used in 
motorcycles, ATVs, snowmobiles, personal watercraft, lawn tractors and golf cars.  It is also 
suitable to maintain larger batteries such as those used in automobile,  marine and farm 
tractors. 

CHARGING INDICATOR

A red LED light indicates that the battery is charging, the green LED light indicates that the 
battery is charged.

AUTOMATIC SHUT OFF 

The battery charger is designed to automatically shut off once battery charging is complete 
to prevent overcharging.  When charging is complete, the green LED will illuminate and the 
charger will be switched to Maintenance mode.  

MAINTENANCE MODE

Once charging is complete, the charger will automatically go into Maintenance mode (also 
known as float mode monitoring). In this mode, the charger keeps the battery fully charged 
by delivering a small amount of current when necessary to keep the battery at peak charge.   

REVERSE POLARITY PROTECTION 

If the cables are incorrectly connected to the battery, the green LED indicator will illuminate. 
Note: the charger will not begin charging if the cables are incorrectly connected to the 
battery. If battery is below X Volts the charger will not charger the battery.  The Green LED 
will illuminate as soon as the battery is attached.  If the RED LED does not illuminate first 
then the battery will not be charged. 
 

OVERHEAT PROTECTION

The charger is designed to shut itself off if overheating is detected.  Once the charger cools 
down, it will resume charging automatically.   

BATTERY CHARGING TIMES 

The built-in intelligent microprocessor will continuously monitor and adjust the charger to 
provide a fast, safe and efficient charge.  Note that battery charge times will vary depending 
on several factors, including: 

8

Содержание 35013













Отзывы: