NPower 35013 Скачать руководство пользователя страница 7

         Never place charger directly above battery being charged.  
         Gases from the battery will corrode and damage the charger. 
         Never set a battery on top of a charger.  
         Never allow battery acid to drip on charger. 
         Always charge a battery in a well-ventilated area. 

        

 WARNING:

 Battery chargers may get hot during operation.  Do not set charger on 

         flammable materials such as carpeting, upholstery, paper, cardboard, etc.  Charger 
         may damage leather, plastic and rubber. 

BATTERY PREPARATION 

         If it is necessary to remove battery from vehicle to charge it, always remove grounded 
         terminal from battery first.  Make sure all accessories in the vehicle are OFF in order to
         prevent sparks.  
         Be sure that the area around the battery is well ventilated while being charged.
         Clean the battery terminals. Be careful to keep corrosion or battery acid from getting in 
         or around your eyes.
         For batteries with removable vent caps, if required, add distilled water to each cell until  
         the battery fluid reaches the level specified by the battery manufacturer. Do not overfill. 
         For batteries without removable vent caps, carefully follow the manufacturer’s charging
         instructions. 
         Study all of the battery manufacturer’s specific precautions and recommendations for 
         charging and for recommended rates of charge.
         Make sure that you have a 12 V lead-acid battery.     
         Determine voltage of battery by referring to the vehicle owner’s manual. 

CHARGING A BATTERY INSTALLED IN VEHCILE

NOTE: 

A marine battery installed in a boat must be removed and charged on shore. To 

charge it on board requires equipment specially designed for marine use.    

         Connect and disconnect the DC output clamps only after removing the AC plug from  
         the electrical outlet.
         Never allow the DC output clamps to touch each other. This may cause a spark.  

FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE.  A 
SPARK NEAR BATTERY MAY CAUSE A BATTERY EXPLOSION.

TO REDUCE THE RISK OF A SPARK NEAR BATTERY: 

1.   Position AC and DC cords to reduce the risk of damage by hood, door, or moving engine  
      part. 
2.   Stay clear of fan blades, belts, pulleys, and other parts than can cause injury to persons.
3.   Check polarity of battery posts. A positive (POS, P, +) battery post usually has a larger 
      diameter than a negative (NEG, N, -) post. 
4.   Determine which battery cable is attached to the vehicle chassis.  

IT IS NORMALLY  

      THE NEGATIVE POST.

  







6

Содержание 35013













Отзывы: