background image

NPK

 

 

- 3 - 

 

 

 

 

 

 

 
 

 

SAFETY    

Safety notices in NPK Instruction Manuals follow ISO and ANSI standards for 
safety warnings: 

 

DANGER  (red)  notices  indicate  an  imminently  hazardous  situation 
which, if not avoided, 

will result in

 

death

 

or serious injury

 

WARNING (orange) notices indicate a potentially hazardous situation 
which, if not avoided, 

could result in

 

death

 

or serious injury.

 

 

CAUTION (yellow) notices indicate a potentially hazardous situation, 
which, if not avoided, 

may result in

 

minor

 

or moderate injury.

 

 

ATTENTION  (blue)  notices  in  NPK  Instruction  Manuals  are  an  NPK 
standard to alert the reader to situations which, if not avoided, 

could 

result in

 

equipment damage.

 

 

1.  Operators and service personnel must read, understand and comply with the 

NPK 

INSTRUCTION MANUAL. 

2.  Keep  personnel  and  bystanders  clear  of  the  SHEET  PILE  DRIVER  while  in 

operation. 

3.  Do  not  operate  the  SHEET  PILE  DRIVER  without  an  impact  resistant  shield 

between the SHEET PILE DRIVER and the operator. 

4.  The  SHEET  PILE  DRIVER  must  not  be  operated  unless  the  operator  is  in  full 

control  of  the  carrier.  Operate the  SHEET PILE  DRIVER 

from the operator’s seat 

only. 

5.  Match  the  SHEET  PILE  DRIVER  size  to  carrier  according  to  NPK 

recommendations.    See  the  CARRIER  MACHINE  COMPATIBILITY  section  of  this 
manual. 

6.  Service personnel must  be cautious handling pins and bushings when exchanging 

the bucket for the SHEET PILE DRIVER.  The carrier machine operator must move 
the stick or boom only when directed by service personnel. 

7.  If it is necessary to hammer the boom pins in or out, beware of flying metal chips.  

Eye protection be worn! 

8.  Do  not  operate the  SHEET PILE DRIVER if the hydraulic oil temperature exceeds 

180° F (

80° C

), or at higher than specified flow rates. 

9.  Be especially cautious around hydraulic lines.  Hydraulic oil can be extremely 

HOT!  

Avoid skin contact with hydraulic oil!  It can cause severe burns! 

10.  Protect  hands  and  body  from  hydraulic  fluids  under  pressure.    Escaping  high 

pressure  fluid  can penetrate  the  skin,  causing  serious  injury.   Avoid  the  hazard  by 
relieving  the  pressure  form  the  hydraulic  system  before  disconnecting  any  lines.  
Search for leaks with a piece of cardboard or other object.  

If an accident occurs, 

seek  medical  attention  immediately!    Hydraulic  fluid  injected  into  the  skin 
must be surgically removed immediately or gangrene may result! 

 

 

Содержание C10CSD


















































Отзывы: