NOVOTEST UT-3M-EMA Скачать руководство пользователя страница 20

 

 

RDC.ED.UT-3M-EMA.000 OM 

Operating manual 

EMA Thickness Gauge NOVOTEST UT-3M-EMA 

Page. 20 

3.2.4.1 The parts replaced during the maintenance 

The  parts  listed  above  have  limited  service  life  and  need  replacement  or  adjustment  with  the 

periods  stipulated  by  the  schedule  of  the  device  maintenance.  For  these  parts,  the  basic  warranty 
applies  before  the  first  part  replacement  or  adjustment.  The  warranty  period  for  each  part  cannot 
exceed  the  limitations  (by  the  time  of  operation  of  the  device  or  working  hours),  specified  in  the 
conditions of the basic warranty. 

 

built-in batteries; 

 

gaskets, if they are removed due to accompanying adjustment; 

 

grease and operating liquids. 
 

3.2.4.2 Wearing parts 

The parts  listed below that have limited service  life  or  need to  be  replaced  (adjusted)  due to  the 

damage. However, these parts are subject basic warranty of NOVOTEST during 12 months: 

 

transducers and their components; 

 

connection cables. 
 

Note:  The  parts  wearing  due  to  friction  (such  as  movable  parts  of  measuring  transducers, 

ultrasonic  piezoelectric  transducers,  support  arm  etc.)  are  not  covered  by  the  basic  NOVOTEST 
warranty,  if  these  parts  fail  due  to  wear  and  tear  during  the  device  operation.  However,  if  in  the 
warranty  period  these  parts  fail  due to  defect  of  material  or  workmanship,  they shall  be repaired  or 
replaced under the basic warranty. 

 

3.2.5 Owner obligations 

The operating manual and registration certificate of the device specifies the information about the 

proper operation and maintenance of the device. 

Proper operation and maintenance of the device will help avoid costly repairs caused by incorrect 

operation, negligence or improper maintenance.  Besides, following our recommendations will extend 
the service life of the device. Therefore, the device owner should: 

 

If any defect or fault is found, submit the device to NOVOTEST or  the authorized dealer 
of  NOVOTEST  for  a  warranty  repair  as  soon  as  possible.  This  can  minimize  the  repair 
required for the device. 

 

Use  only  branded  spare  parts  and  couplants  of  NOVOTEST  (with  appropriate  labels) 
during the device maintenance. 
 

Note:  The  failure  to  perform  the  device  maintenance  in  time  under  the  maintenance  schedule 

deprives of the right to warranty repair or replacement of the faulty parts. 

 

 

Use only branded spare parts and couplants of NOVOTEST (with appropriate labels). 

 

Make  records  of  the  device  maintenance  in  the  registration  certificate  and  keep  receipts 
and bills. If necessary, they will prove that the maintenance was made in time (according 
to periodicity specified in the registration certificate), using the recommended spare parts 
and couplants. This will help in making warranty claims to defects that might occur due to 
a  deviation  from  the  device  maintenance  schedule  or  the  use  of  unauthorized  parts  or 
materials. 

 

Clean the casing of the device and probe according to recommendations of NOVOTEST. 

 

Fulfill the operation and storage requirements in line with NOVOTEST recommendations. 

 

3.2.6 Warranty obligations 

NOVOTEST  warranty  shall  not  apply  if  replacement  or  adjustment  is  caused  by  one  of  the 

following factors: 

Содержание UT-3M-EMA

























Отзывы: