Novell NETWARE 6 Скачать руководство пользователя | Manualshive

Страница: 70 / 152

background image

70

Internetwork Packet Exchange

Internetwork Packet Exchange

103-000176-001

August 29, 2001

Novell Confidential

Manual

99a

38

July 17, 2001

When you enable header compression, you can also specify the number of

compression slots

. A compression slot is a location in router memory that

stores packet header information. The compression algorithm uses this
information to compress outgoing—and decompress incoming—packet
headers.

By default, the number of allocated compression slots is 16. In general, a
session between two end points uses one slot; routing information uses one or
two. Each slot can contain an IPX or an NCP header. When no more slots are
available, packet headers are sent uncompressed, or old slots are reused.

For more information about IPX and NCP header compression and related
topics, refer to

“Header Compression” on page 31

IMPORTANT:

To use header compression, the routers at each end of the

connection must have header compression enabled and must allocate the same
number of

header compression slots

. If the number of compression slots is

different on each router, IPXWAN selects the lesser of the two.

This topic contains the following sections:

“How to Configure IPX and NCP Header Compression on an Interface”
on page 70

“How to Configure IPX and NCP Header Compression per Call
Destination” on page 71

How to Configure IPX and NCP Header Compression on an Interface

To configure IPX and NCP header compression on a WAN interface, complete
the following steps:

1

Load NIASCFG, then select the following parameter path:

Select Configure NIAS > Protocols and Routing > Bindings > a WAN
interface > Expert Bind Options

2

Select Header Compression .

This parameter enables or disables header compression for all IPX
packets sent through this interface. By default, header compression is
enabled on all WAN interfaces; if you want to disable it on the interface,
select Disabled .

3

Select Compression Slots , then enter the number of slots you want to
allocate to this interface.

«
...
68
69
70
71
72
...
»

Содержание NETWARE 6

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для NETWARE 6

Бренд: Gateway Страницы: 138

SX-2000A Series

Бренд: GDC Страницы: 185

digitalSTROM-Server

Бренд: aizo Страницы: 2

Бренд: Axel Страницы: 28

@server xSeries 343

Бренд: IBM Страницы: 193

SuperServer E301-9D-8CN8TP

Бренд: Supermicro Страницы: 117

Бренд: Kontron Страницы: 42

Бренд: Planet Страницы: 74

Бренд: ClearCube Страницы: 2

Бренд: Satel Страницы: 8

Бренд: Inspur Страницы: 112

Бренд: Inspur Страницы: 170

RF-ENCO-IP-HDSDI-35

Бренд: RFoG Страницы: 67

Бренд: 10ZiG Technology Limited Страницы: 2

Бренд: Avere Страницы: 52

Бренд: Acnodes Страницы: 8

Бренд: Gigabyte Страницы: 149

Бренд: ClearCube Страницы: 142

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды