Novanta i401 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 133

background image

I401 GENERAL SPECIFICATIONS

PAGE

|

94

Interlock circuits are often used to disable machinery when a shield, panel, or door is opened. I401’s re-

mote interlock function allows you to connect into an external remote interlock circuit and prevent lasing

by removing DC power from the laser’s RF driver boards when the circuit is electrically “open”.
Lasing is enabled when a Remote Interlock signal is present (INT LED illuminated green), if the RDY LED

is illuminated and a Shutter Open Request signal is applied. Lasing is disabled when the Remote Interlock

signal is removed (INT LED red, RDY LED off). DC power is applied to the RF driver only when the INT

LED is green and the RDY LED is yellow. Remote interlock functionality is provided by the Re-mote

Interlock signal via Pin 3 on the User I/O connector.
To use I401’s remote interlock feature to initiate lasing, apply a voltage in the range of ±5–24 VDC to Pin

3, Remote Interlock. Applying a Remote Interlock signal causes the INT LED to turn green, the RDY

indicator to turn yellow, and sends DC power to the laser’s RF boards. After a five-second delay, a tickle

signal is applied to the tube. When a Shutter Open Request signal is present, PWM Command signals are

enabled to begin lasing. Removing voltage stops DC power from reaching the RF driver, causing the INT

LED to turn red and the RDY LED to turn Off. Lasing remains disabled until a voltage is reapplied to Pin

3.
Your control system can monitor the laser’s remote interlock status on the User I/O connector by

connecting your system’s input to Pin 15, Interlock Open, and Pin 13, Output Common (see Figure 3-16).

This output is closed when remote interlock circuitry is open (INT LED illuminated red). The output is

open (INT LED green) when interlock circuitry is closed.

i401 general specifications

Table 4-6 i401 general specifications

«
...
92
93
94
95
96
...
»

Содержание i401






































































































































Отзывы:

Нет отзывов

Похожие инструкции для i401

Бренд: TaiDoc Страницы: 31

WJHD309 - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 101

Бренд: Panasonic Страницы: 72

KW9M Eco-Power Meter

Бренд: Panasonic Страницы: 2

Бренд: Kawai Страницы: 8

Бренд: GE Страницы: 35

Бренд: Yamaha Страницы: 24

Бренд: Hanna Instruments Страницы: 2

Бренд: Ecolab Страницы: 95

Бренд: Solinst Страницы: 2

Бренд: Bruker BioSpin Страницы: 76

Ocean Optics HR2000 Series

Бренд: Halma Страницы: 42

Бренд: Roland Страницы: 2

Бренд: J&D Electronics Страницы: 2

Бренд: Lumel Страницы: 40

Бренд: ICP DAS USA Страницы: 71

Бренд: CONDTROL Страницы: 11

Бренд: Milwaukee Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды