Nottrot N-COM Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 31

background image

N-COM Setup manual

10

5.1.2

Function and OSD control format

Funtion control of monitors is based on logic addresses (NET ID). Function control is only available from the NControl and
external RS485 commands. The command is addressed to a NET ID in the chain. This command is distributed by NET ID 1
(master) to the slave units. The master will send a replay.

→

Sending a command to any unit in the chain will always have a reply from the 1

st

unit, the master.

When a NControl is used in the chain, this will be the master. The 1

st

monitor in the chain will have NET ID

2

The data package for NCOM function control format:
(fixed)

STX

Address Command Data length Data

Checksum ETX

ACK

0x02 0x01

0x99

0x00

-

Y

0x03

NACK

0x02 0x01

0x15

0x00

-

Y

0x03

GetSoftwareVersion

0x02 0xnn

0x85

0x00

-

Y

0x03

ReplySoftwareVersion 0x02 0x01

0x86

0x02

Data[0], data[1]

Y

0x03

Identify

0x02 0xnn

0x89

0x01

Data[0]

Y

0x03

Setkey

0x02

0xnn

0x94

0x04

Data[0] to data[3]

Y

0x03

GetKey

0x02

0xnn

0x95

0x02

Data[0], data[1]

Y

0x03

GetKeyReply

0x02

0xnn

0x96

0x06

Data[0] to data[5]

Y

0x03

LookupRequest

0x02 0xnn

0xA0

0x00

-

Y

0x03

LookupReply

0x02 0xnn

0xA1

0x12

Data[0] to data[11] Y

0x03

StoreData

0x02 0xnn

0xB0

0x00

-

Y

0x03

For detailed info, please refer to NCOM-protocol XLS

Notes:

-

To store data from RAM to EEPROM use [StoreData 0xB0] command

5.1.2.1

OSD control

OSD function control have a longer response time than dimming.

The data package for OSD function control format:
(fixed)

STX

Address Command Data length Data (0)

Command

Data (1)
Data Type

Data (2)
Data

Checksum ETX

OSDGetSetKeys 0x02 0xnn

0xBA

0x03

0xXX

0xXX

0xXX

Y

0x03

OSDReturnKeys 0x02 0xnn

0xBB

0x03

0xXX

0xXX

0xXX

Y

0x03

Packet

Command

Data Type

Data

Command

Data Type

Data

REMOCON

01

00

00

IRKEY_POWER

01

00

00

IRKEY_POWER

01

00

12

IRKEY_INPUT_SOURCE

01

00

12

IRKEY_INPUT_SOURCE

01

00

03

IRKEY_AUTO

01

00

03

IRKEY_AUTO

01

00

02

IRKEY_MENU

01

00

02

IRKEY_MENU

01

00

05

IRKEY_UP

01

00

05

IRKEY_UP

01

00

0D

IRKEY_DOWN

01

00

0D

IRKEY_DOWN

01

00

08

IRKEY_LEFT

01

00

08

IRKEY_LEFT

01

00

0A

IRKEY_RIGHT

01

00

0A

IRKEY_RIGHT

01

00

0C

IRKEY_AV

01

00

0C

IRKEY_AV

01

00

07

IRKEY_HDMI

01

00

07

IRKEY_HDMI

01

00

06

IRKEY_DVI

01

00

06

IRKEY_DVI

01

00

04

IRKEY_PC

01

00

04

IRKEY_PC

«
...
8
9
10
11
12
...
»

Содержание N-COM
































Отзывы:

Нет отзывов

Похожие инструкции для N-COM

Бренд: JETWAY Страницы: 20

Бренд: Jetter Страницы: 152

Бренд: Eizo Страницы: 2

Бренд: Valor Страницы: 11

Бренд: Genelec Страницы: 2

Бренд: Oricom Страницы: 24

Бренд: Farenheit Страницы: 4

Бренд: Norcent Страницы: 19

Бренд: Nissei Страницы: 72

Two -Way Intercom Monitor

Бренд: Safety 1st Страницы: 5

Бренд: Marshall Electronics Страницы: 2

WearLink Transmitter Nike+

Бренд: Polar Electro Страницы: 8

Бренд: Zenith Data Systems Страницы: 37

Бренд: Graco Страницы: 32

Бренд: AOC Страницы: 1

Бренд: Alienware Страницы: 32

Бренд: Neltronics Страницы: 19

Бренд: Zenith Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды