background image

                         

®

XS

 

240

SELF-PROPELLED TELESCOPIC PLATFORM

12. Be aware of the health risk in hot or chilly working environment.

13. Do not increase the wind load of the Access Platform with extra cover boards or load  
which enlarge the wind surface.

14. Do not increase the reach or working height of the platform by using planks, ladders or  
any other device. Do not swing or jump in the platform.

15. Do not throw down objects from the platform. Make sure that nothing can fall down.

16. Use ear protection when operating the Access Platform from the ground operating  
point,   because   the   sound   intensity   exceeds   84   db   (A).   When   operating   the   Access  
Platform from the platform, the sound intensity is less than 84 db (A), and the use of ear  
protection is not obligatory.

17.   Always   when   you   operate   the   Access   Platform   indoors   or   in   a   place   with   poor  
ventilation, the engine shall only be used for moving the Access Platform. Try to intensify  
the   ventilation.   Risk   of   intoxication!   As   an   accessory,   the   Access   Platform   can   be  
equipped with a mains current pump unit for operation indoors.

18. Do not use the Access Platform as a crane for transporting goods or persons between  
different levels or floors.

19. Do not deactivate a safety device, but repair it or have it repaired by a competent  
maintenance shop before re-use.

20. Ensure that the area below the platform is clear of all personnel and obstructions  
before lowering the platform.

21. To ensure safe and trouble-free functioning of the Access Platform, keep it free from  
snow, ice and other impurities.

22.   Be   very   careful   when   handling   fuels,   lubricating   and   hydraulic   oils   as   well   as  
lubricating   greases   of   the   Access   Platform.   Avoid   skin   contact   with   these.   Risk   of  
exposure!

23. Always turn off the engine of the Access Platform when filling the fuel tank. Beware of  
splashes. Risk of fire!

24. Check and maintain the Access Platform regularly or let a maintenance shop familiar  
with Access Platforms carry out the service and repair work.

25.   Do   not   make   or   cause   to   make   any   structural   alterations   to   the   Access   Platform  
without the permission and instructions of the manufacturer.

26. Do not open the filling opening of the cooling system if the engine is warm. Risk of  
accident!

12

Содержание XS240












































































Отзывы: