Nortrac NorTrac 35XT Скачать руководство пользователя страница 53

Страница: 53 / 98

Maintenance Instructions

Fault

Causes

Troubleshooting

(3) Gear oil pump failure.

(4) Hydraulic oil level is too low.

(4) Add lubricating oil according to the

requirements.

4. Farm implements slowly

drop after being lifted, and

the descent becomes faster

after turning off the engine.

(1) The tightness of the check valve in

the hydraulic flow hydraulic flow

distributor is poor.

(2) The lowering valve is not sealed

tightly.

(3)The oil cylinder safety valve leaks

oil or is not adjusted properly.

(4) The O-ring for the oil cylinder is

damaged or leaking.

(5) The seal ring between the

distributor or the cylinder head and

the oil inlet hole on the 3-point lifter

shell is improperly installed or

damaged.

(1) Clean the check valve.

(2) Clean or replace the lowering valve.

(3) Repair or readjust the safety valve on

the oil cylinder.

(4) Replace the O-ring.

(5) Check and replace the seal ring.

5. With the 3-point lift lever

at lifting position, the

hydraulic distributor makes

a loud noise.

(1) Because of improper adjustment,

the inner lifting arm props against the

lifter case to open the safety valve..

(1) First measure the lifting height of the

farm implement. Then readjust and

shorten the force/position adjusting rod to

make the highest lifting position lower

than the original position.

6. The 3-point hitch has no

hydraulic pressure or weak

output.

(1) The oil cylinder inlet line has been

disconnected.

(2)The front cone and conical hole of

the speed lowering control valve have

not been sealed tightly.

(3) Lifter is in the neutral lifting

position.

(1) Tighten the lowering speed

adjustment knob clockwise to reduce the

lowering speed.

(2) Replace the valve.

(3) Push the lifter control handle to the

lowering position to lower the outer

lifting arm to the lowest position. Shut off

the inlet oil line to the oil tank, and then

put the operating lever in the lift position.

Содержание NorTrac 35XT



































































































Результаты поиска

Содержание NorTrac 35XT

Отзывы:

Бренды по названию

Популярные бренды

Nortrac NorTrac 35XT, Руководство пользователя

Результаты поиска

Содержание NorTrac 35XT

Отзывы:

Бренды по названию

Популярные бренды