Nortrac NorTrac 35XT Скачать руководство пользователя страница 47

Страница: 47 / 98

Maintenance Instructions

Table 2-1 Break-in Time for Each Stage

Unit: hours

2.16 Tractor Faults and Troubleshooting

2.16.1 Chassis Faults and Troubleshooting

2.16.1.1 Clutch Faults and Troubleshooting

Table 2-2 Clutch Faults and Troubleshooting

Fault Causes

Troubleshooting

1. The clutch slips.

(1) The clutch plate and pressure

plate are dirty or greasy.

(2) The clutch plate is excessively

worn or burnt.

(3) The Belleville spring pressure

is too low.

(4) The free play of the pedal is

too small or there is no free play.

(5) The clutch fingers are badly

deformed.

(1) Clean with solvent. Find the cause and

eliminate the fault.

(2) Replace the clutch plate.

(3) Replace the spring.

(4) Re-adjust the free play of the pedal

according to the specifications.

(5) Replace the clutch fingers.

2. The clutch does not
disengage completely, and
noise is heard when it is
engaged.

(1) The free play of the pedal is

too large and the working play is

too small.

(2) The clutch fingers are

excessively warped.

(3) The heads of the three clutch

fingers are not in the same plane.

(1) Adjust the free play of the pedal

according to the specifications.

(2) Replace the clutch fingers.

(3) Adjust according to requirements.

Forward Gear

Reverse Gear

Tractor Gear

Low

High

Low

High

Idle,

load

0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5

Loaded with
3t weight with
a trailer, road
transportation
should be
used

4.5

5 5 2.5

Operating on
sandy soil
with a plow,
tilling depth
14cm (5.5 in)

5 4

Содержание NorTrac 35XT



































































































Результаты поиска

Содержание NorTrac 35XT

Отзывы:

Бренды по названию

Популярные бренды

Nortrac NorTrac 35XT, Руководство пользователя

Результаты поиска

Содержание NorTrac 35XT

Отзывы:

Бренды по названию

Популярные бренды