background image

Northstar

 Explorer D210 

Installation and Operation Manual

7

Master/Slave Selection

To select the master/slave mode of operation:

1.  Apply power while holding down 

.

Hold down during power up

2.  When the unit is on. The display will indicate 

the current display unit:

example

3. Continue 

to 

hold   until the display 

indicates the current master/slave selection.

  

 

 

  Master 

Slave

4. Use   and 

 to change the selection.

5.  To exit this mode, press and hold both 

 and 

 simultaneously.  Alternatively, if no keys 

are pressed for a period of 5 seconds normal 
depth display will resume.

  

Press simultaneously

Note:

 

If the data link is inadvertently broken then 

the display will alternate between -- and -SL.

Linked or Separate Selection

By default a dual station pair of Explorer D210 
instruments automatically keep the following 
settings the same in both instruments:

 Alarms 

On/Off

 

Alarm Values (Deep and Shallow)

 

Keel Offset (see note)

 

Units of measure (see note)

Example: Switching an alarm off on the slave 
instrument will also switch the alarm off 
on the master instrument. The reverse also 
applies, alarms changed on the master will be 
automatically changed in the slave instrument.

Note:

 

The keel offset and units of measure should 

only be changed on the Master instrument.

If independent settings are required the link 
feature can be disabled.

To enable or disable the linked mode:

1.  Apply power while holding down 

.

Hold down during power up

2.  When the unit is on. The display will first 

indicate the current display unit:

Example

3.  Continue to hold 

. The display will indicate 

the current master/slave selection.

Slave

4.  Continue to hold 

 until the display 

indicates the current linked/separate 
selection.

  

Linked

         

Separate

5. Use   and 

 to change the selection.

6.  To exit this mode, press and hold both 

 and 

 simultaneously.  Alternatively, if no keys 

are pressed for a period of 5 seconds normal 
depth display will commence.

  

Press simultaneously

Note:

 

This setup procedure applies to the master 

device and all slave devices. For separate operation 
all devices, including the master, must be set to 
Separate mode. Also, for linked operation all devices, 
including the master, must be set to Linked mode.

OFF

ON

OFF

ON

OFF

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

ON

OFF

ON

OFF

ON

OFF

ON

OFF

OFF

ON

OFF

ON

OFF

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

ON

OFF

ON

OFF

ON

OFF

ON

OFF

OFF

ON

OFF

ON

OFF

ON

OFF

ON

Содержание EXPLORER D210













Отзывы: