NorthStar EXPLORER D210 Скачать руководство пользователя страница 2

Northstar

 Explorer D210 

Installation and Operation Manual

2

FCC Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful interference in a normal installation. This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that interference will not occur in 
a particular installation. If this equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures:

 

Re orient or relocate the receiving antenna.

 

Increase the separation between the equipment and receiver.

 

Connect the equipment into an output on a circuit different from that to which the receiver is 
connected.

 

Consult the dealer or an experienced technician for help.

 

A shielded cable must be used when connecting a peripheral to the serial ports.

IMPORTANT SAFETY INFORMATION

Please read carefully before installation and use.

This is the safety alert symbol. It is used to alert you to potential 
personal injury hazards, Obey all safety messages that follow this symbol to 
avoid possible injury or death.

WARNING indicates a potentially hazardous situation which, if not avoided, 
could result in death or serious injury

CAUTION indicates a potentially hazardous situation which, if not avoided, could 
result in minor or moderate injury.

CAUTION used without the safety alert symbol indicates a potentially 
hazardous situation which, if not avoided, may result in property damage.

DISCLAIMER:

 It is the owner’s sole 

responsibility to install and use the instrument 
and transducers in a manner that will not cause 
accidents, personal injury or property damage. 
The user of this product is solely responsible for 
observing safe boating practices.

BRUNSWICK NEW TECHNOLOGIES INC. AND ITS 
SUBSIDIARIES AND AFFILIATES DISCLAIM ALL 
LIABILITY FOR ANY USE OF THIS PRODUCT IN A 
WAY THAT MAY CAUSE ACCIDENTS, DAMAGE OR 
THAT MAY VIOLATE THE LAW.

Governing Language: This statement, 
any instruction manuals, user guides and 
other information relating to the product 
(Documentation) may be translated to, or 

has been translated from, another language 
(Translation). In the event of any conflict 
between any Translation of the Documentation, 
the English language version of the 
Documentation will be the official version of the 
Documentation.

This manual represents the Explorer D210 
as at the time of printing. Brunswick New 
Technologies Inc. and its subsidiaries and 
affiliates reserve the right to make changes to 
specifications without notice.

Copyright © 2006 Brunswick New Technologies 
Inc. Northstar™ is a registered trademark of 
Brunswick New Technologies Inc

Содержание EXPLORER D210













Отзывы: