background image

 7

INSTALLATION   INSTRUCTIONS

5. Piping and wrapping

Bundle the tubing, connecting cable, and drain 
hose with tape securely,  evenly as shown in 
Fig.12
   Because the condensed water from rear of the 
   indoor unit is gathered in ponding  box and is 
   piped out of room. Do not put anything else in 
   the box.

Indoor unit

Connective
pipe

Pipe room

Ponding box

Wrapping belt

Connective
cable

Drain hose

Fig.12

Connect the indoor unit first, then the 
outdoor unit. 
Do not allow the piping to let out from the 
back of the indoor unit.
Be careful not to let the drain hose slack.
Heat insulated both of the auxiliary piping. 
Be sure that the drain hose is located at 
the lowest side of the bundle. Locating at 
the upper side can cause drain pan to 
overflow inside the unit.
Never intercross nor intertwist the power 
wire with any other wiring.
Run the drain hose sloped downward to 
drain out the condensed water smoothly.

CAUTION

Install the outdoor unit on a rigid base to 
prevent increasing noise level and vibration.
Determine the air outlet direction where the 
discharged air is not blocked. In the case that 
the installation place is exposed to strong wind 
such as a seaside, make sure the fan operating 
properly by putting the unit lengthwise along the 
wall or using a dust or shield plates.
Specially in windy area, install the unit to prev-
ent the admission of wind. If need suspending 
installation, the installation  bracket  should 
accord with technique requirement in the 
installation bracket diagram. 
The installation wall should be solid brick, 
concrete or the same intensity construction, or 
actions to reinforce, damping supporting should 
be taken. The connection between bracket and 
wall, bracket and the air conditioner should be 
firm, stable and reliable.
Be sure there is no obstacle which block 
radiating air.

Strong
  wind

Fig.13

.

.

.

. .

.

.

.

.

.

.

.

.

.

.

.

.

...

..

.

.

.

.

.

.

.

. .

.

Outdoor unit installation 

Outdoor installation precaution

Содержание INVENTER SPLIT-TYPE ROOM AIR CONDITIONER

















Отзывы: