background image

 

 Installation Manual   323-3221-291    Rel 1.0  Standard

 

2-1

 

Installing a VCE

2-

 

Installing a video codec enclosure (VCE) involves receiving it, locating it, and 
mounting it. 

 

Receiving a VCE

 

The VCE and any optional packages ordered are delivered on a transport 
pallet. To verify the shipment before moving the equipment to its final 
location, open or remove the cardboard carefully. You may want to reuse the 
packaging to transfer the equipment to the installation site. If there are any 
packages missing from the shipping order, contact your shipping agent or 
Northern Telecom (Nortel) immediately (the phone numbers are on the 
shipping order). The cabinet may be transported to the installation site by 
hand-truck or carried by two people.

 

Locating a VCE

 

A VCE is designed for indoor use and should be installed in a location which 
provides a minimum of 3 ft (914 mm) clearance on both sides and the front of 
the unit. Additionally, a 1 in. (25 mm) clearance on the top of the cabinet is 
required; see Figure 2-1. Access to 120 Vac power and signal cabling must be 
considered according to local procedures. A VCE cannot be mounted with any 
type of top attachment or side-by-side mounting provision.

 

Figure 2-1
Clearances

Circuit pack removal

3 ft clearance

(minimum)

Access to connectors

3 ft clearance

(minimum)

Cabinet

Cover removal

3 ft clearance

(minimum)

 

Содержание NT2H57UG



















































Отзывы: