manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 74 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 74

74

Chapter 1 About Ethernet Switches 325 and 425

320985-A Rev 01

 

Table 8

 describes the LED behavior at the time of setting the default IP address 

and subnet mask.

You cannot set the default IP address through the CLI, SNMP, Console, or WEB 
interface.

Console port

The Console port allows you to access the Console Interface (CI) screens and 
customize your network using the Console menu options and screens (see 

Chapter 2, “Using the console interface,” on page 93

).

The Console port is a DB-9, RS-232-D male serial port connector. You can use 
this connector to connect a management station or console/terminal to the 
Ethernet Switch 425 by using a straight-through DB-9 to DB-9 standard serial 
port cable. You must use a VT100/ANSI-compatible terminal (for cursor control 
and to enable cursor and functions keys) to use the Console port.

The Console port default settings are: 

•

9600 baud with eight data bits

•

One stop bit

•

No parity as the communications format

Table 8   

UI button LED display during change in IP address and subnet mask

Label

Color/Status

Status

Description

UI

Green

Blinking

The UI button has been pushed. The front panel 
configuration mode has been activated. The 
system is awaiting input.

Steady

The input has been accepted

Amber

Blinking

The input has been rejected

Base

Amber

Steady

The default IP address and subnet mask for this 
unit or stack has been set to 192.168.192.168.

Note: 

The Console port is configured as a Data Communications 

Equipment (DCE) connector. Ensure that your RS-232 cable pinouts are 
configured for DCE connections (see 

Appendix B, “Connectors and pin 

assignments,” on page 425

).

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов