Nortel 425-24T Скачать руководство пользователя страница 425

Страница: 425 / 488

425

System Configuration Guide

Appendix B
Connectors and pin assignments

This appendix describes the port connectors and pin assignments for the Ethernet
Switch 325/425.

RJ-45 (10BASE-T/100BASE-TX) port connectors

The RJ-45 port connectors (

Figure 171

) are wired as MDI-X ports to connect

end stations without using crossover cables. (See

“MDI and MDI-X devices” on

page 426

for information about MDI-X ports.) For 10BASE-T connections, use

Category 3 (or higher) UTP cable. For 100BASE-TX connections, use only
Category 5 UTP cable.

Figure 171

RJ-45 (8-pin modular) port connector

616EA

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 425 / 488

Результаты поиска

Содержание 425-24T

Отзывы: