Nortel 425-24T Скачать руководство пользователя страница 319

Страница: 319 / 488

319

System Configuration Guide

Chapter 8
Ethernet port management using the CLI

This chapter describes how to enable a port, name a port and enable rate limiting.
This chapter covers the following topics:

•

“Enabling or disabling a port”

•

“Naming ports” on page 321

•

“Setting port speed” on page 323

•

“Enabling flow control” on page 326

•

“Enabling rate-limiting” on page 329

•

“Enabling Custom Autonegotiation Advertisements (CANA)” on page 331

Enabling or disabling a port

You can enable or disable a port using the CLI. This section covers the following
commands:

•

“shutdown command for the port”

•

“no shutdown command” on page 320

shutdown command for the port

The

shutdown [port <portlist>]

command disables the port.

The syntax for the

shutdown [port <portlist>]

command is:

shutdown [port <portlist>]

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 319 / 488

Результаты поиска

Содержание 425-24T

Отзывы: