Nortel 425-24T Скачать руководство пользователя страница 320

Страница: 320 / 488

320

Chapter 8 Ethernet port management using the CLI

320985-A Rev 01

Table 106

describes the parameters and variables for the

shutdown [port

<portlist>]

command.

The

shutdown [port <portlist>]

command is in the config-if command

mode.

Figure 124

displays sample output from the

shutdown [port <portlist>]

command.

Figure 124

shutdown [port <portlist>] command output

no shutdown command

The

shutdown

command enables the port. The syntax for the

shutdown

command is:

no shutdown [port <portlist>]

The

shutdown

command is in the config-if command mode.

Table 106

shutdown [port <portlist>]

command parameters and variables

Parameters and
variables

Description

port <portlist>

Specifies the port numbers to shut down or disable. Enter the port
numbers you want to disable.

Note:

If you omit this parameter, the system uses the port number

you specified in the

interface

command.

425-48T(config-if)#shutdown port 2

425-48T(config-if)#

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 320 / 488

Результаты поиска

Содержание 425-24T

Отзывы: