Nortel 2340 Скачать руководство пользователя страница 14

Страница: 14 / 64

Safety Information

NN47250-306 (324121-A Version 01.01)

Wichtige Sicherheitshinweise

Lesen Sie zunächst sämtliche Warn- und Sicherheitshinweise in diesem Dokument, bevor Sie eine der Anweisungen
ausführen.

Benutzer können am Netzgerät dieses Produkts keine Reparaturen vornehmen. Das

Produkt enthält möglicherweise mehrere Netzgeräte. Wartungsarbeiten müssen von

qualifizierten Technikern ausgeführt werden.

Versuchen Sie nicht, das mitgelieferte Netzkabel zu ändern oder zu verwenden,

wenn es sich nicht genau um den erforderlichen Typ handelt. Ein Produkt mit

mehreren Netzgeräten hat für jedes Netzgerät ein eigenes Netzkabel.

Der Wechselstrom des Systems wird durch den Ein-/Aus-Schalter für Gleichstrom

nicht ausgeschaltet. Ziehen Sie jedes Wechselstrom-Netzkabel aus der Steckdose

bzw. dem Netzgerät, um den Stromanschluß des Systems zu unterbrechen.

SICHERHEISMASSNAHMEN: Immer wenn Sie die Gehäuseabdeckung abnehmen

um an das Systeminnere zu gelangen, sollten Sie folgende Schritte beachten:

Schalten Sie alle an Ihr System angeschlossenen Peripheriegeräte aus.

Schalten Sie das System mit dem Hauptschalter aus.

Ziehen Sie den Stromanschlußstecker Ihres Systems aus der Steckdose.

Auf der Rückseite des Systems beschriften und ziehen Sie alle Anschlußkabel

von den I/O Anschlüssen oder Ports ab.

Tragen Sie ein geerdetes Antistatik Gelenkband, um elektrostatische

Ladungen (ESD) über blanke Metallstellen bei der Handhabung der Komponenten zu

vermeiden.

Schalten Sie das System niemals ohne ordnungsgemäß montiertes Gehäuse

ein.

Nachdem Sie die oben erwähnten ersten sechs SICHERHEITSSCHRITTE

durchgeführt haben, können Sie die Abdeckung abnehmen, indem Sie:

Öffnen und entfernen Sie die Verschlußeinrichtung (Padlock) auf der

Rückseite des Systems, falls eine Verschlußeinrichtung installiert ist.

Entfernen Sie alle Schrauben der Gehäuseabdeckung.

Nehmen Sie die Abdeckung ab.

Содержание 2340

































































Результаты поиска

Содержание 2340

Отзывы:

Бренды по названию

Популярные бренды

Nortel 2340, Руководство по установке

Результаты поиска

Содержание 2340

Отзывы:

Бренды по названию

Популярные бренды