background image

Doc No. 700016  Page 16 of 16 

 

3.  User & Operating Instructions. 

3.1 

To Start the Heater 

 

1. Ensure gas supply is turned on. 
 
2. Electrical supply to the controls is on. 
 
3. Ensure that the controls are correctly set 

i.e.; 

 

• 

Clock is correctly set. 

• 

Heater program is correctly set. 

• 

Required room temp is correctly set 

 
4. Once the heating controller ‘calls for heat’ 

power will be supplied to the heater(s). The 
red neon will then illuminate. 

 
5. After a pre-purge period of 10 seconds the 

burner will ignite and the amber neon will 
then illuminate. 

 
6. If lockout occurs press the lockout reset 

button (if available), or switch off electrical 
supply and restart after 15 seconds. 

 
7. If lockout occurs three times consecutively 

switch  off  and  isolate  the  gas  and         
electricity supplies. 
Contact the 

Nortek Global HVAC (UK) Ltd 

Service department.

 

 

 
 
3.2.  To Switch Off Heater 
 

1. Switch off electrical supply to the heater. 

The burner will stop and the fan will shut 
off. 
 

2. If the heater is to be switched off for      

periods in excess of one week it is highly    
recommended that both the gas and the 
electrical supplies are turned off. 
 
 
 

3.3.  Routine Maintenance between Service 

Intervals 

 

After ensuring that the heater is cold and 
mains electric isolated, cleaning of the 

 

 

 

 

 

 

 

reflectors  with  a  soft  cloth  and  a  mild          
detergent (non solvent based cleaners only) 
in water can be undertaken. 

 

Additional removal of dust from the radiant 
tubes, burner and heat exchanger can be   
undertaken. 

 
 
 

3.4   Frequency of Servicing 
 

The manufacturer recommends that to 

 

 

ensure 

continued 

efficient 

and 

safe         

operation 

of 

the 

appliance 

it 

is                 

recommended that the heater is serviced 
annually by a competent person e.g. every 
year in normal working conditions but in 
exceptional dusty or polluted conditions 
more frequent servicing may be required. 

 

The manufacturer offers a maintenance 

 

 

 

 

service. 

 

Details are available on request. 

 

For Service requirements, please contact   

Nortek Global HVAC (UK) Ltd.

 

 

For further technical and service support 
visit our Support Information Database at     
www.s-i-d.co.uk 

Document refe

re

nce number 

GB/

VS/190

A

/0815

 

Replaces GB/VS/190A/0112

 

Nortek Global HVAC is a registered trademark of Nortek Global HVAC Limited. Because of continuous product innovation, Nortek Global HVAC reserves the right to change product specification without due notice. 

 

NORTEK GLOBAL HVAC (UK) LTD 

Fens Pool Avenue 

Brierley Hill 

West Midlands  DY5 1QA 

United Kingdom 

 

Tel: 

01384 489 250

 

Fax: 

01384 489 707

 

 

[email protected] 

www.ambirad.co.uk 

Registered in England No. 1390934. Registered office: 10 Norwich Street, London, EC4A 1BD 

Содержание Ambirad Vision VSX

















Отзывы: