Nortech F10 Скачать руководство пользователя

Страница: 14 / 16

F10

Earth Fault Indicator

Page 14 of 16

Specification

6.1

General

Power Supply

3.6V Lithium battery. The battery is plug in for simple
replacement.

Threshold current

45 Amps nominal

Indicator

Ultra bright LED
1.5 seconds flash rate
3 –24 hours duration (as ordered) or until reset by
manual (button) or voltage reset

Remote Alarm options Volt free change-over contacts. Normally open and

normally closed contacts are provided.

DC Remote Reset

12V-24V dc for 500ms

AC Remote Reset

110V-230V ac for 10 seconds

6.2

EMC

The F10 indicator has been designed and tested for compliance accordance
with the high level standard 61326-1:2006. The class tested to was
Industrial.

Immunity

ESD

IEC61000-4-2

4kV contact, 8kV air

EM Field

IEC61000-4-3

10V/m 80MHz-1GHz
3V/m 1GHz-2GHz
3V/m 2.0GHz-2.7GHz

Power Freq Mag Field

IEC61000-4-8

Not Applicable

Power and I/O Signal Lines

Burst (Fast Transient) IEC61000-4-4

Not Applicable

Surge

IEC61000-4-5

Not Applicable

Conducted RF

IEC61000-4-6

Not Applicable

Voltage Dips and
Interruptions

IEC61000-4-11 Not Applicable

Voltage Dips and
Interruptions

IEC61000-4-11 Not Applicable

Emissions

Radiated Emissions

EN55011

Class B

Insulation

1kV RMS for 1 minute insulation tests on NO/NC contact

Not called for by the standard

Содержание F10

















Результаты поиска

Содержание F10

Отзывы:

Похожие инструкции для F10

Бренды по названию

Популярные бренды

Nortech F10, Руководство пользователя

Результаты поиска

Содержание F10

Отзывы:

Похожие инструкции для F10

Бренды по названию

Популярные бренды