Nortec RH Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 60

background image

25 |

Start Up

Nortec Digital Controls

Nortec provides optional On/Off and Modulating digital controls. Figure 25 show the function
and meaning of the Digital Control’s display and buttons. All controls are available either wall
mounted or with a remote sensor for duct mounting.

Figure 25: Modulating and On/Off Digital Control Operation

Modulating Control

The modulating controls use a PI control algorithm to transmit a 0-10V control signal to the
humidifier. Adjust the setpoint to the desired setting by using the up/down arrow buttons on

the controller.

On/Off Control

The On/Off controls use a PI control algorithm to open and close a relay that opens and closes
the humidifier’s On/Off loop. Adjust the setpoint to the desired setting by using the up/down

arrow buttons on the controller.

Note:

It is possible to field calibrate Nortec digital controls if the displayed humidity is found to
be different than a known trusted source. See chapter on Troubleshooting starting on
page 45.

Output signal is shown on
modulating controller
proportional to the demand.

State of On/Off humidistat

Setpoint (RH%)

Humidity (RH %)

Indicates the

humidistat is on.

A half moon

indicates it is off.

Snowflake indicates the

setpoint is being

overridden by outdoor

temperature.

Option button accesses
sensor calibration.
See troubleshooting

Increase / Decrease Setpoint

Power button turns

off the humidiistat if

pressed for 2 seconds

«
...
26
27
28
29
30
...
»

Содержание RH





























































Отзывы:

Нет отзывов

Похожие инструкции для RH

Бренд: Guardian Страницы: 12

Humiperfect NH890

Бренд: Novita Страницы: 19

Бренд: Zibro Страницы: 8

Бренд: Turbo Страницы: 24

Бренд: Germ Guardian Страницы: 18

Бренд: Vornado Страницы: 32

Бренд: Neptronic Страницы: 44

Бренд: Black & Decker Страницы: 24

Бренд: Black & Decker Страницы: 14

Бренд: Sealy Страницы: 4

Бренд: Philco Страницы: 38

Бренд: Cooper&Hunter Страницы: 8

Бренд: Cooper&Hunter Страницы: 20

Бренд: UFESA Страницы: 44

Бренд: Parker Zander Страницы: 60

Бренд: EMAG Страницы: 2

Honeywell Home TrueSTEAM HM512

Бренд: resideo Страницы: 4

Бренд: Vortice Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды