Norma Icon-5 Скачать руководство пользователя страница 1

Страница: 1 / 22

TDMG0002 Icon-5 Maintenance Guide

– Version: 02 – Release date: 2020-04-27

Icon-5 Maintenance Guide

Kit description and procedures

This document describes the contents of the maintenance kit and list the corresponding
maintenance procedures for Norma Icon-5 automated hematology analyzer.

Special tool required:

UNF tool

(not included in the kit)

Please contact our support team at

[email protected]

if further information or

clarification is required.

Icon-5 Maintenance Kit (HAT827A)

– for 1-year/10.000 sample period

Item

Part#

pcs

Aperture maintenance kit

HAT809A

Peristaltic pump tube set for “gray” and “orange”

pumps

HAT800B

HAT800C

1 pair of each

Lubricants (in small containers)

Shell Retinax lubricant (red)

HAT829A

Teflon based grease (white)

HAT829B

Silicone grease (clear)

HAT829C

Piercing needle with UNF screw and “O” ring

HAT165A

Greiner BIO Vacutainer NO add w/o rubber in cap

(White)

HAT823B

Содержание Icon-5























Результаты поиска

Содержание Icon-5

Отзывы:

Похожие инструкции для Icon-5

Бренды по названию

Популярные бренды

Norma Icon-5, Руководство по обслуживанию

Результаты поиска

Содержание Icon-5

Отзывы:

Похожие инструкции для Icon-5

Бренды по названию

Популярные бренды