norix PRD100 Скачать руководство пользователя страница 8

Страница: 8 / 13

Wall end uses Hook Tab

Exposed end uses Straight Tab

Hook faces end

of bed

13.

Install Anchor Tabs on Bed

In this

installation

, the wall end of the unit

will receive a Hook Anchor, and the

exposed end will receive a Straight

Anchor Tab. Use whichever hook that will

point to the wall on the end. For further

clarification, see the illustration on page 9,

step 16.

Install the brackets using (2) 5/16" Screws.

11.

Install Floor Anchors and Brackets

If floor anchors other than the provided Concrete

Wedge Anchors are to be used, consult the

manufacturer for proper installation.
If the provided Concrete Wedge Anchors are to

be used, drill (4) 5/16" dia. holes a minimum of 1"

deep into the floor at the locations where

previously marked.
Vacuum debris from the holes.
Place the (2) Brackets back into their locations as

shown and install the Concrete Wedge Anchors,

securing the Hex Nuts tightly to the Brackets.

Ensure that the Brackets are still aligned with the

centerline and the vertical face is still aligned with

the 3" mark. Make adjustments if necessary.

It is

critical that these brackets are installed inline and

in the correct position.

The provided Shims can

be used to help level the brackets.

12.

Drill Hole and Install Brackets Onto Bed

Refer to page 3 and the section on

Drill Holes

and Install Brackets Onto Bed.

Using the Drill Guide, drill a hole in

only

the

exposed end of the Bed. Do not drill a hole in the

end that goes against the wall. Either end of the

bed can be drilled, but the Hook Anchor in the

next step must face toward the wall as shown.

Use the appropriate Hook Anchor.

Page 8 of 13

Rev. C - 10/20/20

091-989

Содержание PRD100














Результаты поиска

Содержание PRD100

Отзывы:

Бренды по названию

Популярные бренды

norix PRD100, Руководство по сборке

Результаты поиска

Содержание PRD100

Отзывы:

Бренды по названию

Популярные бренды