manualshive.com logo in svg

norix PRD100, Руководство по сборке

Поделиться
Скачать
norix PRD100 Скачать руководство пользователя страница 2

 

 

 

Connect the two "T"s

using a chalk line

or straight edge

Section I

Mid-wall installation with long side against wall:

Note:  In this installation, the Left and Right Anchor Hooks 

will not be used.

Both

 Ball Lock Pins and Guide Tubes 

will

 be used.

1.  

Marking the Location

Place the Bed on the floor in an upright position in the 

location where it is to be installed, 

pushed tight against the 

wall

.

2.  Mark a line on the floor along the 

ends

 of the bed, 

toward the center.

3.  Locate the molded line at the center of each end, and 

mark the floor at this location, perpendicular to the first 

line.  When finished marking, you will have what looks like a 

letter "T" on the floor at each end.

4.  Move the Bed aside.

5.  Using a straight edge or chalk line, mark a line down the 

center, by connecting the bases of the two "T"s that were 

drawn in step 3.

Bed

open areas

See appropriate section depending on location of installation:

Section I:  Mid-wall installation with long side against wall, page 2

Section II: 

 

Mid-wall installation with short side against wall, page 6

Section III:

 

Corner installation, page 10

  

Page 2 of 13

Rev. C - 10/20/20

091-989

Содержание PRD100














Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды