manualshive.com logo in svg

Noritz SCU-401-12M, Руководство по установке, Страница: 31 / 39

Поделиться
Скачать
Noritz SCU-401-12M Скачать руководство пользователя страница 31

System controller

External operation switch Terminal

External operation switch

Connect to terminals

External 

operation

 switch

Pressure 

switch

Remote

controller

●  Connect the external operation switch when you want to turn ON/OFF the water heater from external 

in addition to the Power ON/OFF Button of the remote controller.

-  If the terminal of the external operation switch is switched from open to short, the Power ON/OFF 

Button of the water heater is turned "ON".

-  If the terminal of the external operation switch is switched from short to open, the Power ON/OFF 

Button is turned "OFF".

15VDC, 2.7mA

Thermostat Terminal

Thermostat of 

the hot water storage tank

Connect to terminals

Thermostat

Remote

controller

15VDC, 2.7mA

External 

operation switch

Thermostat

●  Use the normally open relay with the contact for low voltage.

●  For the external operation switch

-  Whether the Power ON/OFF Button is synchronized or not to the cycle operation can be changed by 

switching the setting.

  (it can be changed only for recirculation system).

  If the external switch is switched from open to short, the setting is switched as shown below.

  Power ON/OFF Button is synchronized:        Power ON/OFF Button is turned "ON", 

                                                                           cycle operation is turned "ON"

  Power ON/OFF Button is not synchronized:  only Power ON/OFF Button is turned "ON"

●  Connect the thermostat of the hot water storage tank.

-  If the temperature of the hot water storage tank exceeds the temperature set with the thermostat, 

the contact in the thermostat is opened and the circulation pump stops.

-   A platinum resistance temperature detector cannot be connected directly.

●  This terminal is short-circuited when the product is shipped from factory. 

  When you use this feature, disconnect a short-circuit connector as shown below.

●  This terminal is short-circuited when the 

product is shipped from factory. 

  When you use this feature, disconnect a 

short-circuit connector as shown below.

Disconnect this connector 

when external operation switch is connected.

Disconnect this connector 

when thermostat is connected.

─31─

Содержание SCU-401-12M








































Отзывы:

Нет отзывов