Noritz ProTough BNR98-DVC-LP Скачать руководство пользователя страница 33

33

     Changing Other Features

  Adjusting the Temperature / Water Quantity Display

  Note: The setting must be done within the first 10 minutes of connecting electrical power to the water heater.
Table of Setting Items

                   Item                                         Choices (factory defaults shaded)                    

Celsius/Fahrenheit 

display mode.

°F (Fahrenheit) / gal

°C (Celsius) / L

Display

Power On/Off Button

ENTER Button

      Setting Procedure

1.  Turn the water heater off by pressing the Power On/Off Button on the remote controller.

2.  Disconnect, then reconnect electrical power to the water heater.

3.  Press the MENU Button inside the cover, select "Initial settings" using the ▲/▼ Buttons.

4.  Press the ENTER button, the "Initial settings" screen appears on the display.

5.  Select "[°F / gal] <

----

> [°C / L]" using the ▲/▼ Buttons.

6.  Press the ENTER Button and select either [°F / gal] or [°C / L] using the ▲/▼ Buttons.
7.  Press the ENTER Button, "Set complete Please wait..." appears on the display for 5seconds and 

then the "Initial settings" screen appears on the display.

8.  To confirm the setting, turn the water heater on by pressing the Power On/Off Button on the remote 

controller.

      Remote Controller

▲/▼ Buttons

MENU Button

Содержание ProTough BNR98-DVC-LP


































Отзывы: