Noritz ecOTOUGH NRC1111-DV-LP Скачать руководство пользователя страница 10

10

7.

 Installation 

Securing to the wall

Illustration

Check

4. Drill holes for the remaining four screws.

5. Hang the unit again by the fi rst screw, and then 

insert and tighten the remaining four screws.

6. Take waterproofi ng measures so that water does 

not enter the building from screws mounting the 
device.

•  Make sure the unit is installed securely so that it will 

not fall or move due to vibrations or earthquakes.

1. Drill a single screw hole, making sure to hit a stud.

2. Insert and tighten the screw and hang the  unit by  

the upper wall mounting bracket.

3. Determine the positions for the remaining four screws 

(two for the top bracket and two for the bottom), and 
remove the unit. 

•  The weight of the device will be applied to the wall. If the strength of the wall is not 

suffi cient, reinforcement must be done to prevent the transfer of vibration.

•  Do not drop or apply unnecessary force to the device when installing. Internal parts may 

be damaged and may become highly dangerous.

•  Install the unit on a vertical wall and ensure that it is level.

Locating Screw Holes

Mounting

Structure

•  When installing with bare hands, take caution to 

not infl ict injury.

•  Be careful not to hit electrical wiring, gas, or water 

piping while drilling holes.

Item

CAUTION

Be sure to do

Mounting Bracket
(upper)

Location of Screw Hole

Locating Screw Holes

Installations at Elevations 

Above 2,000 ft.

• Adjust the dip switches as illustrated in the table to 

the right if this water heater is installed at an altitude 
of 2000 ft. (610m) or higher. 

•  D i s c o n n e c t  p o w e r t o  t h e  w a t e r  h e a t e r  b e f o r e 

changing the dip switches. Failure to perform this 
step will result in a "73" code displayed on the remote 
controller and a cease in operation.  If this occurs, 
disconnect, then reconnect power to the water heater 
to reset the system.

  Note : Please refer to page 28 for the location of the 

dip switch bank.

Tapping Screw

* Do not change any other dipswitches.

* High elevation adjustment.

6

5

2,001 - 4,000 ft (611 - 1,220m)

0 - 2,000 ft (0 - 610m)

ON=

OFF=

4,001 - 6,000 ft (1,221 - 1,830m)

6,001 - 8,000 ft (1,831 - 2,440m)

Содержание ecOTOUGH NRC1111-DV-LP










































Отзывы: