background image

25

gas. The gas heating value based on sea level
can be obtained from your  local gas utility. The
heating value of gas at high altitude is always
lower than the sea level heating value. The
heating values used in Tables 6 & 7 are based
on sea level values.

Natural Gas High Altitude Conversion

All factory shipped furnaces are ready to oper-
ate between zero and 4999 ft. above sea level.
For higher altitudes (between 5000 and 10,000
ft. above sea level), conversion can be achieved
simply by adjusting the furnace manifold pres-
sure as shown in Table 6.

LP/Propane Gas Conversion

IMPORTANT NOTE: When converting a low
NOx furnace from Natural gas to LP/pro-
pane gas, it is necessary to remove the NOx
Baffles from the furnace.

Conversion of this furnace to utilize LP/propane
gas must be made by qualified service person-
nel, using factory authorized or approved parts.
Conversion to LP/propane gas can be accom-
plished by first replacing the natural gas orifices
with the appropriate LP/propane orifices shown
in Table 8 or 9.  Note: for installations between

Table 8. Natural and LP Gas Orifice Sizes

for Elevations between zero and 4999 ft.

Above Sea Level

Table 9. Natural and LP gas Orifice Sizes

for Elevations between 5000 and 10,000

ft. Above Sea Level

Furnace Rating

Furnace Rating

Plate Input (Btu/h)

Nat

LP

Plate Input (Btu/h)

Nat

LP

60,000 45

55

60,000 45

56

72,000 43

54

72,000 43

55

96,000 43

54

96,000 43

55

120,000 43

54

120,000 43

55

Orifice Drill Size

Orifice Drill Size

For a LP Gas Sea Level Heating Value of 2,500 Btu/hr.

Elevation (feet above sea level)

zero to 

1999

2000 to 

4999

5000 to 

5999

6000 to 

7999

8000 to 

10000

Manifold Pressure Setting (in WC)

Full Input

10

8.5

10

9

8.5

Low Input

5.5

5.5

6.5

6.5

6.5

Table 6. Manifold Pressure (in WC) for Natural Gas at Various Altitudes

Table 7. Manifold Pressure (in WC) for LP/Propane Gas at Various Altitudes

For a Natural Gas Sea Level Heating Value of 800 to 899 Btu/cu.ft.

Elevation (feet above sea level)

zero to 

1999

2000 to 

4999

5000 to 

5999

6000 to 

7999

8000 to 

10000

Manifold Pressure Setting (in WC)

Full Input

3.5

3.5

3.5

3.5

3.0

Low Input

1.7

1.7

1.7

1.7

1.6

For a Natural Gas Sea Level Heating Value of 900 to 999 Btu/cu.ft.

Elevation (feet above sea level)

zero to 

1999

2000 to 

4999

5000 to 

5999

6000 to 

7999

8000 to 

10000

Manifold Pressure Setting (in WC)

Full Input

3.5

3.5

3.5

3.2

2.8

Low Input

1.7

1.7

1.7

1.6

1.5

For a Natural Gas Sea Level Heating Value of 1,000 to 1,100 Btu/cu.ft.

Elevation (feet above sea level)

zero to 

1999

2000 to 

4999

5000 to 

5999

6000 to 

7999

8000 to 

10000

Manifold Pressure Setting (in WC)

Full Input

3.5

3.5

3

2.8

2.5

Low Input

1.7

1.7

1.5

1.4

1.3

Содержание TA-060C-08A









































Отзывы: