Nordson 1006453A Скачать руководство пользователя страница 23

Ejector Gun Controller

19

E

2001 Nordson Corporation

All rights reserved

1006453A

Issued 6/01

Manual 25-23

To order parts, call the Nordson Customer Service Center or your local
Nordson representative.  Use the parts list, and the accompanying
illustration, to describe and locate parts correctly.

Numbers in the Item column correspond to numbers that identify parts in
illustrations following each parts list.  The code NS (not shown) indicates
that a listed part is not illustrated.  A dash (—) is used when the part
number applies to all parts in the illustration.

The number in the Part column is the Nordson Corporation part number.
A series of dashes in this column (- - - - - -) means the part cannot be
ordered separately.

The Description column gives the part name, as well as its dimensions
and other characteristics when appropriate.  Indentions show the
relationships between assemblies, subassemblies, and parts.

Item

Part

Description

Quantity

Note

0000000

Assembly

1

1

000000

S

Subassembly

2

A

2

000000

S S

Part

1

S

If you order the assembly, items 1 and 2 will be included.

S

If you order item 1, item 2 will be included.

S

If you order item 2, you will receive item 2 only.

The number in the Quantity column is the quantity required per unit,
assembly, or subassembly.  The code AR (As Required) is used if the
part number is a bulk item ordered in quantities or if the quantity per
assembly depends on the product version or model.

Letters in the Note column refer to notes at the end of each parts list.
Notes contain important information about usage and ordering.  Special
attention should be given to notes.

8. Parts

Using the Illustrated Parts
List

Содержание 1006453A

























Отзывы: